Search results

full dead ang unit..kaya pull out q ang shorted...shorted ang PA..ngunit walang pamalit PA number RDA 6232 make this jumper nalang..fried and tested finished product

RTO ng other tech..nka ilang palit na ng touch screen pero ayaw talaga mag work...kaya banatan q... check q all lines ng touch connector ok namn lahat...kaya voltage check..drop VCC ng touch ic kaya...try hanap ang salarin.. replace nyo yan..fullshorted ang pinakamaliit na caps jan sa area na...

may pattern po ang unit pero hnd mkapasok sa recovery dahil ang ang nakalagay CUSTOM BINARY BLOCK BY FRP (secure fail:recovery) kaya try mag flash ng combi file..pero error..pit file error..try q mag flash sboot pero parin.. kaya heto ang solution open ang UMT GSM..then select samsung click...

baka may maencounter kayo..ayaw ma touch..palit touch..failed parin..check terminal kung open traces..wala nmn akong nakita..check voltage missing 2.8 volts..kaya heto nalng solution..jump nyo nalng po..ika 7 pin ng LCD connector..papunta sa 2V8 ng terminal ng touch screen..

https://mega.nz/#!iKhTRQKY!tKgGnjTcxmyWo-dOvZVv_ei4b9fdH_-TF058pljdQIk heto gamit q..sana may maitulong...

baka may mangailangan... https://www.4shared.com/rar/emYuEwWIea/SP7731E__Cherry_Mobile__Flare_.html?

baka meron nka buck up n sa cm2...spd po xa...baka may mabait na mg upload ng firmware neto..salamat

baka meron nka buck ng emmc dump neto mga...9008 mode aang unit...try q flash bootloader..dead parin..baka merong nka buck up sa inyo..maraming salamat...

https://drive.google.com/file/d/1auk5CPym1G6V9kV0jSYd0YJmxd6NEqiR/view heto po tested DA file reset nyo nlng sa nck

ayaw mag charge ng unit kapag nka off..hnd lumabas charging indicator...pero kapag nka on ng chacharge xa..pero ayaw lang lang tumass ng percent charge nya..kaya heto solution just replace po yung nka red na IC na yan... heto result nyan..

...nag update c tomer ng cp nya..ayon hang nalng..medyo risky c unit..baka ma todas kaya try q UMT formatfs done pero hang parin..kaya buck up then flash..ayon n deado sa UMT.. try q balik buck up..success..pero dead parin..nka 9008 mode.. then try CM2,,ayon na dale..success buhay unit...then...

water damage po ang unit..kaya konting linis sa curroded part..pero same parin...kaya try q tirahin backlight section..hndi namn na bigo... check ang replace po yung nka yellow..backlight ic then schotsky diode... finish product

ptpa..looking for samsung sm-a520f good board..baka meron po kayo..kunin q kaagad..maraming salamat...

AA6C-46E8-0B51-2453-6D4D-2014-7700-4FB7 pa try boss..error sa akin keygen nya..

water damage po ang unit..kaya try this jumper.. heto na result

pasa ni kapwa tech..hnd kaya dw dahil...hnd kaya sa talkback...kaya try q new method... sundin nyo lang procedure.. heto result

https://www.4shared.com/rar/LUc6zy4uee/MT6572_NAND_alps__Mate10_mini_.html heto firmware na gamit q.. logs ni cm2 Brand : alps ProdModel : Mate10 mini Device : k403_mate10_mini_2g AndroidVer: 5.0.1 MTKxCPU : MT6572 MTKxPRJ : ALPS.KK1.MP7.V1.5

wala boot key

iclick lang namn sa UMT..open UMT QCfire then select model.. heto po testpoint''' ayon success..

2 days palang ky tomer ang unit...nalimutan na pattern..kaya punta xa dito.. open c UMT MTK...then select vivo y91.. thn click format fs.. hntayin matapos.. ayun wala na c pattern pero may frp pa.. kaya click reset frp hntayin matapos..kwarta na..

dead po ang status ng unit...check q battery interface..ayon full shorted xa kaya hanapin ang faulty... remove nyo lang po yung nka red..may isa po jan na shorted na caps...

no service status ng unit..kaya make this jumper... ok na yan... sana may maitulong

change nyo lang po ang ecaps na to...shorted po iyan.. heto po result nyan.. pera na...

tested in oppo..no virus https://gsmcracktools.blogspot.com/2019/02/inferno-unitool-v157-full-cracked-free.html sundin nyo lng po instruction hw to run a software

para mpadetect po ang unit short nyo lang po ang TX to ground then try q NCK detected na...kaya format userdata.. wala n password..pera na..