Search results

MACBOOK HARDWARE REPAIR BASIC SUPPORT ARE ON, JUST POST A HELP THREAD AND I WILL TRY TO ANSWER IT.

PINOYTECHNICIAN FORUM PINOYTECHNICIAN BOHOL CHAPTER ATTENDANCE MONTH OF NOVEMBER 2023

PINOYTECHNICIAN FUROM PINOYTECHNICIAN BOHOL CHAPTER SEPTEMBER 2023 ATTENDANCE

Reball CPU lang lods ✅

CHECK 5V FROM CHARGING CONNECTORS IF GOOD THEN PROCEED TO BATTERY CONNECTOR ON BOARD IF NOT PRESENT 3.8V TO 4.2 OR 4.3 PROCEED CHARGING IC REFER TO BOARD VIEW CHECK IV MAY 5VBUS IF MERON CHECK 4.2 VBAT PAG WALA, TRY REBALL CHARGING IC, PAG NO LUCK REPLACE DONE

PINOY TECHNICIANS FORUM BOHOL CHAPTER

COMMENT LANG

PINOYTECHNICIAN.COM BOHOL CHAPTER CHAPTER MEMBER ATTENDANCE, MONTH OF FEBRUARY 2023

PINOYTECHNICIAN.COM BOHOL CHAPTER CHAPTER MEMBER ATTENDANCE, MONTH OF JANUARY 2023 NAME: SHOP LOCATION:

1. VISUAL CHECK, FOUND OUT NA PUTOL UNG LINYA NG BACKLIGHT SA FLEX NG LCD SO I DID BY JUMPING THE CONNECTION 2. PAG TEST KO WALA PADIN SO I DECIDED CHECKING THE LCD CONNECTOR ON BOARD PARTICULARLY SA LINES NANG BACKLIGHT FOUND OUT OL READING ON THIS PIN PERO REMAINDER LNG CASE TO CASE PO...

1. RESTORE UNIT QUICK FLASH SA 3UTOOLS SELECT LATEST IOS VERSION 2. Jailbreak on 12.4 I am using mackbook pro 3. Go to unlocktools Select Apple tab UNTETHERED BYPASS (meid) FULL NOTIFICATION B

Heading agad sa Network power supply ic REBALL DONE ✅

OPEN PTC TICK REALME TAB SELECT REALME C2 FORMAT SELECT FACTORY RESET HOLD VOL UP AND DOWN SALPAK USB WAIT TILL FINISH G

mtk First for password, do hard reset, alam mo na yan! for frp, open act unlocktool pro, nasa free soft section, pm mo saken hw at name mo! tick erase frp, off unit, tick start, hold up and down vol. salpak usb, done in 3 sec.

PROCEDURE:  DOWNLOAD AVENGER MAIN V1.8 Pag na DL nyo po Install and open napo natin si Avenger Main V1.8 Dapat naka off cp select po SpreadTrum Diag Click Enter Diag connect usb cable then hit Factory Reset for FRP WATCH THIS

PROCCEDURE: DOWNLOAD AVENGER MAIN V1.8 Pag na DL nyo po Install and open napo natin si Avenger Main V1.8 Dapat naka off cp select po SpreadTrum Diag Click Enter Diag connect usb cable then hit Factory Reset

NEED TESTED FW PO

Pa help po. wala akong makita sa net diagram dito

CHARGING PORT:OK CHARGING BOARD : OK FLEX CABLE: OK VBUS TP: 5V PRESENT PERO WALANG CHARGING VOLTAGE PAPUNTANG BATTERY

binaklas ko at tiningnan ko yan, kaso hindi naman marumi ang "#", at ket tinanggal ko na ang metal ganun parin so nag decide nako na e reheat si cpu at di naman ako nabigo.

Pag open nang camera app, rear cam lang, tapos pag mag shift na nang front, AYAW pumasok, bumabalik sa rear cam. Nag replace lang ako nang lcd dahil unresponsive na ang touch screen nya. At sa hindi kopa binuksan gumana naman si front cam. Pag balik ko, wala na, ayaw na pumasok sa front...

First dl mo to https://drive.google.com/file/d/14QT2-inqfKXGptTd7EKqbG0x-_3oh3U3/view Kasama na ang Samsung driver, at odin, may provided link dyan 2. Enter download mode, vol up, home and power, press that simultaneously 3. Unzip downloaded file and install necessary tools. 4. Salpak usb...

1. Open backcover 2. Tanggal connected cables sa MoBo 3. Via Diode mode, tinest ko ang power button at ayun 0 resistance,nag beep 4.linis nalang sa switch mismo, yung tatlong metal. yan linis nalang, then boom ok na