6300 New Pinout's 10 Pin's done by Infinity
Problem;
Dead
Tool's
Infintiy
Rj45 Pinouts
Procedure
1.Open Inifinity Shell.
2.Go to china phone Nokia/6300/click run Tab.
3.Connect RX,TX and GND to the Phone.
4.Go to Service Tab /click Format FFS[FFs;Complete] wait until finish
5.change Imei/Click write imei tab.
Picture and Logs;
Pinout's
Format FFS;
Code:
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: "format ffs"
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:2C03:0008
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
detecting chip #01 in region #00...
flash: 01227E22202200:18E59F00000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.4F7C8377.[JIA6300_PCB01_GPRS_MT6225_S00.MAUI_07A_W07_52_MP_V2.BIN_E70F29F2].rpl
identification#1 detection finished
device-id: 4F7C8377
identification#1 protocol ver: 04
ver. sw1: JIA6300_PCB01_GPRS_MT6225_S00.MAUI_07A_W07_52_MP_V2.BIN
ver. sw2: MAUI.07A.W07.52.MP.V2, 0DD6F018
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 01227E22202200:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
reading: eeprom[JIA6300_PCB01_GPRS_MT6225_S00.MAUI_07A_W07_52_MP_V2.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[JIA6300_PCB01_GPRS_MT6225_S00.MAUI_07A_W07_52_MP_V2.BIN]_20080823-104231.B0E.bin
flash: 01227E22202200:18E59F00000000
Backup required data Done
Patch required data...
Patch required data Done
Special operation...
Special operation Done
Write...
Write Done
Finalization...
formatting...
flash: 01227E22202200:18E59F00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\system_log_4F7C8377_JIA6300_PCB01_GPRS_MT6225_S00.MAUI_07A_W07_52_MP_V2.BIN_E70F29F2_20080823-104253.B0X.bin
Finished, time used: 273 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !Change Imei;
Code:
Action: imei
imei write method: mode-2
imei write channel: imei #1 for dual sim/mono-CPU
new imei: 356960016358249
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:2C03:0008
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: MAUI.07A.W07.52.MP.V2
Version: 6300_HW
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
detecting structure #2...
0 done
44 byte(s) read
verification...
verification done: 35696001635824
Finished, time used: 14 sec
Remove/Install battery now !Done;
