- Joined
- Jun 12, 2014
- Messages
- 973
Boot Repair Tool Marvell chip Samsung
Supported List
SM-J100F
SM-J100FN
SM-J100M
Symptom
No power up / Not Powering On
Unable to Download mode
Instruction
-Brief Process
1: Install usb Driver for Marvell Chipset.
2: Run "CSDownloader"
3: Load Recover File and Download that file to Device
-to Download Recovery file to device Short-circuit for TP has Required
Pre-requisites
1: usb driver file
Driversfor Marvell.zip
the install file for windows x86/x64 bit are located in that file
2: Pc Program For Recovery
CSDownloader.zip
3: Recovery File
RecoverBoot_SM-J100F_OA3.zip
4: Repair Firmware
Warning...!
I'm not responsible for any damages will be held!
Do at your own Risk!
Looking for Password? use our
"TRIANGLE Button"
We will give it to you for Free...!
Boot Recovery Process
1: install usb driver for "Marvell"
Unzip the " Drivers for Marvell.zip" and Run the install file for each Windows7 versions.
→ For Windows7 32bit : Run "DrvInstaller.exe"
→ For Windows7 64bit : Run "DrvInstaller_x64.exe"
2. Step for recovery
Unzip the "CSDownloader.zip" and Run "CSDownloader.exe"
3: Unzip the "RecoverBoot_SM-J100F_OA3.zip"file and
Load "RecoverBoot_SM-J100F_OA3.bin" to CSDownloader.
Click "Go" button to start downloading.
Then "Stop" button will be displayed on the tool
4: Short circuit for TP download pin and Ground(GND) by tweezers.
Connect the phone to PC via USB cable and Attach a battery while short circuit TP and
GND by tweezers.
When CSDownloader detect the device , Recovery binary will be downloaded
automatically.
If the recovery is succeed, progressive bar will be displayed as green color with "Success"word.
Download full SW to the device
Enter download mode, using ‘Volume down’ + ‘Home’ + ‘Power’ key.
If the phone is successfully recovered, phone will enter download mode.
you can now flash your phone using Repair Firmware
Supported List
SM-J100F
SM-J100FN
SM-J100M
Symptom
No power up / Not Powering On
Unable to Download mode
Instruction
-Brief Process
1: Install usb Driver for Marvell Chipset.
2: Run "CSDownloader"
3: Load Recover File and Download that file to Device
-to Download Recovery file to device Short-circuit for TP has Required
Pre-requisites
1: usb driver file
Driversfor Marvell.zip
the install file for windows x86/x64 bit are located in that file
2: Pc Program For Recovery
CSDownloader.zip
3: Recovery File
RecoverBoot_SM-J100F_OA3.zip
4: Repair Firmware
Warning...!
I'm not responsible for any damages will be held!
Do at your own Risk!
Looking for Password? use our
"TRIANGLE Button"
We will give it to you for Free...!
Boot Recovery Process
1: install usb driver for "Marvell"
Unzip the " Drivers for Marvell.zip" and Run the install file for each Windows7 versions.
→ For Windows7 32bit : Run "DrvInstaller.exe"
→ For Windows7 64bit : Run "DrvInstaller_x64.exe"
2. Step for recovery
Unzip the "CSDownloader.zip" and Run "CSDownloader.exe"
3: Unzip the "RecoverBoot_SM-J100F_OA3.zip"file and
Load "RecoverBoot_SM-J100F_OA3.bin" to CSDownloader.
Click "Go" button to start downloading.
Then "Stop" button will be displayed on the tool
4: Short circuit for TP download pin and Ground(GND) by tweezers.
Connect the phone to PC via USB cable and Attach a battery while short circuit TP and
GND by tweezers.
When CSDownloader detect the device , Recovery binary will be downloaded
automatically.
If the recovery is succeed, progressive bar will be displayed as green color with "Success"word.
Download full SW to the device
Enter download mode, using ‘Volume down’ + ‘Home’ + ‘Power’ key.
If the phone is successfully recovered, phone will enter download mode.
you can now flash your phone using Repair Firmware
