MFC Dongle Initial Setup Full Instructions (Update 2014-11-27)★★★★★

[.::Gsmdenis::.]

MFC WITH A LOT OF NEW FEATURES





START FROM NOW


① First you must Register a account on MFC official website with valid Email .

Once you done, you will got this message.

Success

You have successfully registered. Please check your email for further information!

② Verify your account with Token code (This code will be received by register email)

A. Go to your email inbox. you will go this :​

B. Input your registered email and the Token code to activate your account :​

Once you done, you will got this message.

Success

You have successfully activated your account!

③ Once your account activated, then you can go to login page access to site.

④ Go to this public download page to get the Dongle Driver and Serial Number Reader:

1. Install Dongle Drivers from DongleDrivers directory by running InstallDriver.exe This will install mfc120.dll required for the program to start.
2. Install vcredist_x86 for 32 bits windows or vcredist_x64 for 64 bits windows from MicrosoftRedistributables directory
3. To install the dongle update driver you need to connect MFC dongle to computer in BOOT MODE (you can open n****ad.exe first so all the oputput from MFC dongle will be written there). This will install libusb0.dll driver required for the program to start. In order to connect MFC dongle in BOOT MODE you need to connect P0 and GND(P zero) pin together (see images below) using the RED cable we provided in the pack.

Note : MFC Dongle is detected correctly and appears as USB Input Device

• If MFC dongle is not detected properly (An exclamation sign is displayed in the icon next to USB Input Device) you need to right click and press Uninstall to uninstall the drivers then connect the MFC dongle again so that Windows can install the standard USB Drivers again.
• When MFC dongle is correctly detected you can check it’s Hardware IDs and you will see that it has an VID of 04D9 and PID 1702. REV might vary depending on the update you use.

When Dirver installed then Open MFCSNReader_0.2.exe and input the dongle to computer USB port to get the Serial Number.​

⑤ Now go to User Dashboard please click Manage Memberships , input the Serial number, Press Activate Membership, then you will have full download permissions.

⑥ Now go to Download page to download all MFC dongle software.

How to Start and do related settings:

① Sensor-Connection-MFC Dongle (How to connect ?)

• 5v => 5v
• GND => GND
• OUT => P2

② Downloading Server Client and getting latest software.

• Download MFCDL_2.0.exe
• Run MFCDL_2.0 and press the start button
• Select the appropriate update and press next, This will get the latest version.

③ Running Software/ settings etc

• Run MFC_1.1.4.exe (or higher / newer) you just downloaded
• Select any option from the drop down box and tick update, now you can input the dongle to computer. this will upgrade your dongle firmware. and then do the setting (you can keep it as default) after Tick write and its ready to use.

Now you can close the Software, and take out MFC Dongle from computer, start to unlock your phone.​

④ About MFC Software interface Description:

1. MFC Dongle software interface with version information. E.g. V1.14
2. MFC Dongle Serial Number
3. MFC Dongle Update information
4. MFC Dongle write Auto default configure data information
5. Once Software write Auto default configure data / Or customize setting , you can Click here then insert the MFC Dongle to test if the output is correct!
6. Click here to open our official website , www.mfcbox.com
7. Click here to open our official support forum , forum.gsmhosting.com/vbb/f936/
8. MFC Dongle Support Models , You can choose related tab to Configure what action you want to be performed
9. Update selection
10. Upgrade your dongle using selected update
11. You can also adjust settings later or just keep default configure data
12. Test the light sensor, only works if the update inside the dongle is compatible
13. This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases
14. This start value - You can also adjust settings later or just keep default configure data
15. E.g. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on
16. This usually represents the delay between codes. On iOS 7.x the delay must be at least 4300 (5 seconds). Please read update details for more info on what this delay represents
17. Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc
18. Read information from dongle like settings and codes etc.
19. To close the software button

⑤ Macbook unlock settings etc

A. iCld 13 Pro Retina, iCld 13 Pro, iCld 15 Pro Retina, iCld 15 Pro which means:​

Macbook pro /Macbook pro retina 13'' 15''

iCld mean the Macbook locked from icloud.com website , MFC supported for unlocked

B. About Macbook EFI Boot Mode ?​

Using this method code recovery time maximum 33 hours for all 9999 possible codes(1 codes each 12 seconds)

How to:

• Update dongle using EFI Boot Mode
• Write the appropriate settings using the software (the delay in milliseconds is 12000 for EFI Boot Mode) 12 seconds / code
• Connect the light sensor to the computer in a gray area of the screen while you are in the EFI Boot Screen.
• Once unlocking is done the dongle will start blinking
• You can read now the dongle using Online Update software and you will see the latest used code.The real unlock code is usually the one before that. So if you see 1999 then it means the real code is 1998.

• Just press Option & Alt key (is same button) after turning on , Button must be pressed immediately after reboot before device appears the apple logo.

• So when we using EFI Boot Mode unlock Macbook, you should connect the light sensor to the computer in a gray area of the screen while you are in the EFI Boot Screen.

C. iCld 13 Pro Retina, iCld 13 Pro, iCld 15 Pro Retina, iCld 15 Pro​

Using this method you can recover a 4 digits iCloud Pin with the speed of about 5 codes/minute for a maximum of 33 hours.

How to:

• Update dongle with the appropriate update;
• The delay option is very important and is depending on the speed of your computer reboot.
• After 5 codes are checked Dongle needs to reboot your computer. So using a stopwatch you can
• Manually use the Reboot button and calculate how many seconds are there until you are back to the iCloud pin screen.

If for example you have 34 seconds reboot time then you need to write 34000ms as delay

• This update does not require light sensors;
• Just write settings and start recovering your pin

D. iCloud custom settings:​

Using this method you can recover a 4 digits iCloud Pin with the speed of about 5 codes/minute for a maximum of 33 hours. ! Not working on MAC OS Yosemite 10.10.X !

How to:

• Connect the light sensor on the last digit displayed by the computer (in the white area of that digit)
• Adjust the location values of the Reboot button and the Wifi Popup Cancel if this is available. You can do it by trying values until you reach the correct location and the computer is automatically rebooted.
  • For example for Macbook Pro 13 inch old model the values of Reboot Button are X:565 Y:-105, Macbook Retina 13 inch the values are 556,-65
• You can try other settings until you find the correct one and don't forget to share
• The delay option is important and is depending on the speed of your computer reboot.
• With a stopwatch you can manually use the Reboot button and calculate how many seconds are there until you are back to the iCloud pin screen.
  • If for example you have 34 seconds reboot time then you need to write 34000ms as delay.

We improved this update compared with previous ones in order to use the light sensor to better detect the right moment when to input the next code so usually even lower values will work but in case they don't please adjust this to a higher value ,Just write settings and start recovering your pin

 

[.::Gsmdenis::.]

A simple guide to know the dongle work or not work:

Sometimes when we unlocking phone by MFC, you may wanna to know If the dongle in working condition.


Here is the testing guide

When you unlocking:

You may covered the sensor by sponge or some tape.

A, Remove sponge or tape , and remove the sensor form the cable. give some light to the sensor, then dongle LED light will be get very fast blinking mode.

B, Now the dongle will be stop sending command to phone

C, Remove the USB cable from the phone

D, Insert the dongle to computer, press read

E, Check the last index value from logs

Now you will know the Dongle If in working condition.

The fast way to unlock your phone ,Here have some way may help you :

A, If you know your phone code maybe 2xxx

Then you can setting the start value with 2000

B, If you know your phone code between 2500 -3000

You can using above A method, you also can setting your start value is 3000, and click on DESCENDING ORDER

C, What we will add this function

If you know your phone code is 3456 or 3546 or 3645 etc , we will add a function just unlock in those 4 digits.