share ko lang gawa ko ngayun brown tab1 passcode issue done sa cm2 dongle
ito po yung info nya!
BB_CPU_PID : 6797
BB_CPU_NME : [MediaTek] Helio[X20]|MT6797_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0002
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
DAgent configured successfully
Connection agent : PRELOADER
DRAM already initialized by Preloader
Link with DAgent established
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , 2304F
[eMMC] : FLASH_CID : 450100444634303332014B3FC70094D5
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID : 0x74F71010A6D45315C314CD8281CB5C74
INT RAM : 0x00000000
EXT RAM : 0xC0000000 [3 GiB]
[NAND] : FLASH : NOT INSTALLED
[UFSM] : FLASH : NOT INSTALLED
[HSUSB] : MODE : HIGH-SPEED
Boot Ok!
[AP] : Initial info read Ok!
Brand : brown
ProdName : brown_tab1
ProdModel : brown tab1
Device : brown_tab1
AndroidVer: 7.1.1
MTKxCPU : MT6797
MTKxPRJ : alps-mp-n1.mp9-V1.6.1_rlk6797.6m.rc.n_P60
1. Open CM2MT2
2.power off ang unit tapos need cable AND cm2 dongle
3.click service select FULL FACTORY (WIFE+FRP)
4.Click Reset Settings /Format FS
5. Salpak usb Cable no boot key antayin lang matapos at on muna ang unit after done na
At binackup kuna din after mag done sana makatulong
ITO PO YUNG LINK:
1.21 GB file on MEGA
mega.nz
ito po yung info nya!
BB_CPU_PID : 6797
BB_CPU_NME : [MediaTek] Helio[X20]|MT6797_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0002
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
DAgent configured successfully
Connection agent : PRELOADER
DRAM already initialized by Preloader
Link with DAgent established
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , 2304F
[eMMC] : FLASH_CID : 450100444634303332014B3FC70094D5
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000747C00000
[eMMC] : FLASH_UCP : 29820 MiB [eMMC 32 GiB]
DEV RID : 0x74F71010A6D45315C314CD8281CB5C74
INT RAM : 0x00000000
EXT RAM : 0xC0000000 [3 GiB]
[NAND] : FLASH : NOT INSTALLED
[UFSM] : FLASH : NOT INSTALLED
[HSUSB] : MODE : HIGH-SPEED
Boot Ok!
[AP] : Initial info read Ok!
Brand : brown
ProdName : brown_tab1
ProdModel : brown tab1
Device : brown_tab1
AndroidVer: 7.1.1
MTKxCPU : MT6797
MTKxPRJ : alps-mp-n1.mp9-V1.6.1_rlk6797.6m.rc.n_P60
1. Open CM2MT2
2.power off ang unit tapos need cable AND cm2 dongle
3.click service select FULL FACTORY (WIFE+FRP)
4.Click Reset Settings /Format FS
5. Salpak usb Cable no boot key antayin lang matapos at on muna ang unit after done na
At binackup kuna din after mag done sana makatulong
ITO PO YUNG LINK:
1.21 GB file on MEGA
mega.nz