mga boss bka mkatulong sa inyo, redmi note 3 mtk firmware,
miui8 upgrade to miui9, nsa link na ang firmware at instructions,
mga 10 mins xa magoopen,pag success na,hintayin nyo lng
at pag matagal mag load ung playstore download lng kau ng bago sa google
https://www.foldertips.com/android/rom-global-hennessy-non-ubl/
Before installing this ROM , first fulfill the following requirements and materials.
Requirements before flashing :
Run SP Flash Tools by Right Click » Run as Administrator on the flash_tool.exe file ;
.. until a display like the following appears..
Then click the Download Agent button ;
.. and navigate to the file MTK_AllInOne_DA.bin which is in the SP-Flash-Tool-v5.1532.00 folder ;
Then click Open ;
Then click the Scatter-loading button ;
.. and navigate to the file MT6795_Android_scatter.txt which is in the /images folder of the extracted ROM;
.. until the end result is like the following image:
Watch this !
Uncheck userdata so that the data in your Internal Storage is not deleted (optional);
Keep system and boot checked ;
Uncheck preloader , unless your cellphone is hard bricked.
If so, make sure the dropdown option is selected Download only , then click the Download button ;
Furthermore,
Turn off the smartphone;
Press and hold the Vol Down button then immediately connect the Redmi Note 3 MTK to your PC/laptop using a USB cable until a Red Bar (Red Bar) appears at the bottom of the SP Flash Tools (if your device is detected) .
Keep holding the Vol Down button and release it if this Red Bar has turned Yellow , which means the flashing process is running.
Wait for the process until the Yellow Bar is completely completed and the flashing process is successfully marked with a green checklist as follows..
Until this stage the flashing process is complete and try to turn on the cellphone by pressing the Power button a little longer than usual.
Done.
The first boot process takes longer than usual, this is normal. Just wait until you get to the homescreen and do the reset..
Here are the results on my Redmi Note 3 MTK ..
Secure 4G network..!
miui8 upgrade to miui9, nsa link na ang firmware at instructions,
mga 10 mins xa magoopen,pag success na,hintayin nyo lng
at pag matagal mag load ung playstore download lng kau ng bago sa google
https://www.foldertips.com/android/rom-global-hennessy-non-ubl/
Before installing this ROM , first fulfill the following requirements and materials.
Requirements before flashing :
- Make sure your Redmi Note 3 MTK battery is fully charged or at least 50%; ( This is mandatory, if you don't believe me, read this article Flashing Success HP Still Doesn't Turn On? Beware of Low Battery! ) ;
- Original or good quality USB cable;
- PC/Laptop with OS Windows 7 and above by disabling driver signature .
- MultiROM MIUI 9 v9.2.2.0 (Lollipop / Bahasa Indonesia) – 857 MB » Mediafire | Onedrive | Google Drive (extract and place it on drive C:\ or in a folder without spaces) ;
- Download SP-Flash-Tool-v5.1532.00.zip – 43 MB (Use only this SP Flash Tools , because other versions will fail due to verification of unsigned ROM. Extract and place in C:\ drive )
- Install Xiaomi Android USB Driver and MT6577_USB_VCOM_Drivers.zip – 400 KB . If Redmi Note 3 is also not detected on the computer, try installing the VCOM drivers manually here ;
Run SP Flash Tools by Right Click » Run as Administrator on the flash_tool.exe file ;
.. until a display like the following appears..
Then click the Download Agent button ;
.. and navigate to the file MTK_AllInOne_DA.bin which is in the SP-Flash-Tool-v5.1532.00 folder ;
Then click Open ;
Then click the Scatter-loading button ;
.. and navigate to the file MT6795_Android_scatter.txt which is in the /images folder of the extracted ROM;
.. until the end result is like the following image:
Watch this !
Uncheck userdata so that the data in your Internal Storage is not deleted (optional);
Keep system and boot checked ;
Uncheck preloader , unless your cellphone is hard bricked.
If so, make sure the dropdown option is selected Download only , then click the Download button ;
Furthermore,
Turn off the smartphone;
Press and hold the Vol Down button then immediately connect the Redmi Note 3 MTK to your PC/laptop using a USB cable until a Red Bar (Red Bar) appears at the bottom of the SP Flash Tools (if your device is detected) .
Keep holding the Vol Down button and release it if this Red Bar has turned Yellow , which means the flashing process is running.
Wait for the process until the Yellow Bar is completely completed and the flashing process is successfully marked with a green checklist as follows..
Until this stage the flashing process is complete and try to turn on the cellphone by pressing the Power button a little longer than usual.
Done.
The first boot process takes longer than usual, this is normal. Just wait until you get to the homescreen and do the reset..
Here are the results on my Redmi Note 3 MTK ..
Secure 4G network..!
Last edited by a moderator:
