1. dinala sa shop ng naka reset na kaya proceed na tayo sa 1st step.
2. disassemble si unit para sa testpoint mas maganda kung check info muna para makita mo kung anu sec. patch before you proceed sa 2nd step.
Device : Samsung SM-A015F
Operation : Read Information
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM8)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00002000
OPK_DATA : 6C429E6D6583C49ADCAF169BD1A23255CCED44DF35B7F8A7A4F9795AED7AF713
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_044]...Done
Executing Loader...OK
Hardware : 8937, EMMC, 16 GB
LU Count : 3 [0x01D5A000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Software : RP1A.200720.012.A015FXXU4BUD8, A015FXXU4BUD8 [Tue Apr 13 21:11:27 +07 2021]
Android Ver. : 11
Patch Level : 2021-04-01
USERDATA : Encrypted
You can use DISABLE LOCKS to Disable Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 7.
3. connect ulit si TP insert usb port then click lang si frp reset at hintayin lang matapos.
4. done dalan done..
godbless us all....
2. disassemble si unit para sa testpoint mas maganda kung check info muna para makita mo kung anu sec. patch before you proceed sa 2nd step.
Device : Samsung SM-A015F
Operation : Read Information
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM8)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00002000
OPK_DATA : 6C429E6D6583C49ADCAF169BD1A23255CCED44DF35B7F8A7A4F9795AED7AF713
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_044]...Done
Executing Loader...OK
Hardware : 8937, EMMC, 16 GB
LU Count : 3 [0x01D5A000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Software : RP1A.200720.012.A015FXXU4BUD8, A015FXXU4BUD8 [Tue Apr 13 21:11:27 +07 2021]
Android Ver. : 11
Patch Level : 2021-04-01
USERDATA : Encrypted
You can use DISABLE LOCKS to Disable Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 7.
3. connect ulit si TP insert usb port then click lang si frp reset at hintayin lang matapos.
4. done dalan done..
godbless us all....