SKK HYPER X CORE DEAD done via cm2 first here in ant.

[verser09]

Dinala dead, charge ko may pumapasok na amphere mga 0.01
so idecide i shock ang battery built in sya look.
ingat nlng sa pagtangal ng back case
lalo na sa camera

DEAD pa din sya at di padin nag chacharge
try ko din i format muna ala din
after mga 5 mins nag pakita yung logo na kidlat yun nga lang walang charging

so decide iProgram

read muna:

Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : SKK
Device Model : HYPER_X_CORE
Device CPU : MT6580
Device IntName : HYPER X CORE
Device Version : 6.0
Device Compile : 12/3/2016 4:42:08 AM
Device Project : alps-mp-m0.mp1-V2.34_droi6580.we.m_P16
Device ExtInfo : HYPER X CORE


tapos hanap ng exact same firmware>

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 53 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513832334D4200D1EADAF1930F
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM328
[eMMC] : FLASH_CID : 150100513832334D4200D1EADAF1930F
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB [eMMC 16 GiB]
DEV RID : 0xBE4195C57E62C7352D121F3A71B9D6DC
INT RAM : 0x00020000
EXT RAM : 0x80000000 [2 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6580 , Project : wf162e_zthx , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3780 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000003320000
Erase : 0x00000000050A0000-0x000000039DCE0000
Flash Pre-Erase Done, time used : 00:00:08

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_wf162e_zthx.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0014
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:07:56

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:21

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:08:37
Reconnect Power/Cable!

ilang segundo lang ay eto na sya )

tapos

then

tested maraming salamat sa mayari ng firmware!!
ok sa cam sa imei sa lahat..


FIRMWARE:
https://mega.nz/#!oZBWmRBS!HPyt_lwX_q1X11cvuK1ihfXhMdhRZ6qc-Z5QAQqkc0M

pass: ilovesign

 

[KeanLi]

Hi sir...pwede po bang malaman ang password??

 

[rdctel23]

unit: skk hyper x core
problem: no power
action taken: backup original file (no power)
then write full flash via nck crack
status: working

salamat po sa info: ganun din po sa fw.... malaking tulong po ito

INFO CM2

[AP] : Initial info read Ok!

Brand : SKK
ProdName : HYPER X CORE
ProdModel : HYPER X CORE
Device : HYPER_X_CORE
AndroidVer: 6.0
MTKxCPU : MT6580
MTKxPRJ : alps-mp-m0.mp1-V2.34_droi6580.we.m_P16

SECURITY :
IMEI_SW [1] : 35939107453XX19
IMEI_SW [2] : 3593910745322XX
BTMAC Addr : FA84466580E6
WiFi MAC : 003ABEDB71ED

Done!
Elapsed: 00:00:15
Reconnect Power/Cable!

WRITE FULL FLASH NCK CRACK

Flash files count is :11
Action : Firmware update.
Selected 0-By CPU: MT6571_EMMC
Exe version: NCKDongle AndroidMTK 2.5.6.2
Scenario: Full Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM10)
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6580_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 2 GB DRAM
----------------------------------------------------
EMMC: (116Gb+16384Mb) SAMSUNG 0x513832334d42
EMMC FW VERSION: 00:00:00:00:00:00:00:00
EMMC CID: 15010051383233 : 000000000000000000
EMMC UA SIZE: 0x3a3e00000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x3a4a00000 [14.572 GB]
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM12)
Flash EMMC Algo Start.
Starting flash.
FORMAT EMMC FLASH : BEGIN: 0x97800000 - LEN: 0x10000000
FORMAT EMMC FLASH : BEGIN: 0xa7800000 - LEN: 0x2fb580000
Send preloader...
Download firmware to flash now...
Wait untill phone will start charging.
All done.

 

[mark29]

boss pa pm password tnx

 

[ChunChun]

Tested bossing!