World First : MediaTek MT6595 FULL and REAL support 
Unlike some copypasters, moving around , We make new and real stuff
So, lets start with MT6595.
While others show read info log , or show nothing, just empty "mtxxx" support, without any propper tests and e.t.c. , We make all things, which should be and sure - all they are working.
Read Full info ( including HW, Modem, Langs and e.t.c. )
O
Read Factory Firmware
Result is same as factory one. It fully compatible with SPFT
World first and e.t.c.
Factory Firmware Flashing
World first and e.t.c.
Security Repair
World first and e.t.c.
It REALLY work
Take a note!!!
After "Security Repair" it can fail to"DL image fail"! (Lenovo will fail to this mode 100%) Use "Fix DL" option to fix that!
Fix DL Errors
[
SP Unlock ( "Code read" and "Direct Mode" as well )
World first and e.t.c.
Format FS
PatternLock Read
World first and e.t.c.
UserLocks Reset (Gmail,Pin,Password and e.t.c.)
World first and e.t.c.
Read PhoneBook
World first and e.t.c.
It save data in 4 different formats, including apple,google,vcf,and human readable.
Dump Reading/Writing , Repair Preloader, Fix Unknown BaseBand, NVRAM Read/Write and e.t.c. also work, but they are not mandatory.
Reply With Quote
Unlike some copypasters, moving around , We make new and real stuff
So, lets start with MT6595.
While others show read info log , or show nothing, just empty "mtxxx" support, without any propper tests and e.t.c. , We make all things, which should be and sure - all they are working.
Read Full info ( including HW, Modem, Langs and e.t.c. )
O
Code:
peration : Check / Read Info [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Lenovo
ProdName : x2eu
ProdModel : Lenovo X2-EU
Device : X2-EU
AndroidVer: 4.4.2
MTKxCPU : MT6595
MTKxPRJ : X2-EU_ROW_S117_1410101350
MODEM :
BaseBand : MT6595_S00_X2_EU_V26_1_lwg_n
EXTRA :
LCD [0] : nt35595_fhd_dsi_vdo_lg
LCD [1] : otm1902a_fhd_dsi_cmd_tianma
LCD Res : 1920x1080
TOUCH [0] : S3528
CAM [0] : imx214_mipi_raw
CAM [1] : ov5693_mipi_raw
MODEM : mt6595k95_hspa_lwg_x2eu
LOCALE : en_US es_ES zh_CN zh_TW ru_RU pt_BR fr_FR de_DE tr_TR it_IT in_ID ms_MY vi_VN ar_EG th_TH pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ iw_IL my_MM km_KH ko_KR pl_PL es_US bg_BG hr_HR lv_LV lt_LT sk_SK uk_UA de_AT da_DK fi_FI nb_NO sv_SE en_GB bn_BD ka_GE
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!Result is same as factory one. It fully compatible with SPFT
World first and e.t.c.
Code:
Operation : Read Flash [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Conent now ...
Brand : Lenovo
ProdName : x2eu
ProdModel : Lenovo X2-EU
Device : X2-EU
AndroidVer: 4.4.2
MTKxCPU : MT6595
MTKxPRJ : X2-EU_ROW_S117_1410101350
[Read Ok] : preloader_x2eu.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : preload.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[ScatCFG] : MT6595 / V1.1.2 / x2eu / EMMC
FW Size : 1897 MiB
Scatter saved to : E:\MT6595__Lenovo__Lenovo X2-EU__X2-EU__4.4.2__X2-EU_ROW_S117_1410101350\
All done!
Done!
Elapsed: 00:07:36
Reconnect Power/Cable!World first and e.t.c.
Code:
Scatter Load Ok , BaseBand : MT6595 , Project : x2eu , Storage : EMMC
Files found : 10 , Set to Flash : 9
Ready to Flash!
Operation : Flash [ v1.27 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6595 , Project : x2eu , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : Only one records found, and determined as universal
BL : eMMC supported by BootLoader!
BL : Flash Pre-Erase
Total blocks to Erase : 1
Erase : 0x0000000001C80000-0x0000000744F00000
Flash Pre-Erase Done, time used : 00:00:03
SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_x2eu.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0010
Update PMT by user request
Repartition Done!
Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : PRELOAD
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:04:11
Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : SECRO
Verify Passed : LOGO
Verify Passed : PRELOAD
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:04
Update Mirror PMT
Update Done!
Update RomInfo done
Done!
Elapsed: 00:04:33
Reconnect Power/Cable!World first and e.t.c.
It REALLY work
Code:
Operation : Repair Security [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
IMEI [00] : 866156020xxxxxx
Set IMEI [00] : 099644327654346
Prepare finished. Security check required!
Wait for phone...
Phone found! [ 63 ]
Sync...
PostCheck Ok! Repair done!
Done!
Elapsed: 00:00:54
Reconnect Power/Cable!After "Security Repair" it can fail to"DL image fail"! (Lenovo will fail to this mode 100%) Use "Fix DL" option to fix that!
Fix DL Errors
[
Code:
CODE]Operation : Fix DL Errors [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Done!
Elapsed: 00:00:20
Reconnect Power/CableSP Unlock ( "Code read" and "Direct Mode" as well )
World first and e.t.c.
Code:
Operation : SP Unlock [ v1.27 ]
Mode : Read Codes
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
SIM [1] codes :
[1] Level , [Locked] : False
[2] Level , [Locked] : False
[3] Level , [Locked] : False
[4] Level , [Locked] : False
[5] Level , [Locked] : False
[6] Level , [Locked] : False
[7] Level , [Locked] : False
SIM [2] codes :
[1] Level , [Locked] : False
[2] Level , [Locked] : False
[3] Level , [Locked] : False
[4] Level , [Locked] : False
[5] Level , [Locked] : False
[6] Level , [Locked] : False
[7] Level , [Locked] : False
Done!
Elapsed: 00:00:20
Reconnect Power/Cable!Format FS
Code:
Operation : Format FileSystem [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Backup : Skipped by user request
FMT Mode set to : 0
Format : Cache and UserData (Full Factory Reset)
Format CACHE block
Format block Ok!
Format UDA block
Format block Ok!
Done!
Elapsed: 00:00:28
Reconnect Power/Cable!World first and e.t.c.
Code:
Operation : Read PatternLock [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading data ...
FS Size : 27538 MiB
Magic Ok
Mount point : /data
Get PatternLock ...
PatternLock Sequnce : 12547
Done!
Elapsed: 00:00:50
Reconnect Power/Cable!World first and e.t.c.
Code:
Operation : Clear UserLocks [Pin/Pwd/Pattern/FVLock/GoogleAcc] [ v1.27 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
LSSA Ok!
LSSW Ok!
LSSS Ok!
LSSG Ok!
Security Settings : Clear Ok!
[Info] : Android 5.x / MT67xx : If phone stuck on "Logo"
1. Wait 2-3 minutes. Power Off phone by long press "Power" button
2. Power On phone again
3. Or wait up to 3-7 minutes, until phone start by itself
4. Also recommended reboot phone twice before start use it
Done!
Elapsed: 00:00:20
Reconnect Power/Cable!Read PhoneBook
World first and e.t.c.
It save data in 4 different formats, including apple,google,vcf,and human readable.
Code:
Operation : Read UserData [ v1.27 ]
PhoneBook : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 63 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6595
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6595_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004257424333520259EA4F759109
DA Stat : v3.2 on BBID : 0x8C
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : R3CBW
[eMMC] : FLASH_CID : 1501004257424333520259EA4F759109
[eMMC] : FLASH_LEN : 0x0000000747C00000
INT RAM : 0x00020000
EXT RAM : 0x80000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Step #1
Step #2
Read Ok, PhoneBook records extracted : 10
TXT Saved to : C:\Infinity\CM2\CM2MTK\PhData\MT6595_PhoneBook.txt
Write : 10
CSV Saved to : C:\Infinity\CM2\CM2MTK\PhData\MT6595_PhoneBook.csv
Write : 10
VCF Saved to : C:\Infinity\CM2\CM2MTK\PhData\MT6595_PhoneBook.vcf
Write : 10
VCFv3 Saved to : C:\Infinity\CM2\CM2MTK\PhData\MT6595_PhoneBook_v3.vcf
Done!
Elapsed: 00:00:16
Reconnect Power/Cable!Dump Reading/Writing , Repair Preloader, Fix Unknown BaseBand, NVRAM Read/Write and e.t.c. also work, but they are not mandatory.
Reply With Quote
Last edited by a moderator:
