What's new
By:
PinoyTechnician

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

1280 no power pero ok sa program

JMGadgets

JMGadgets

Registered
Joined
Jul 26, 2014
Messages
656
Reaction score
0
Points
81
Location
Angono Rizal
MCU: V 07.00 11-09-12 RM-647 (c) Nokia
IMEI: 354635052748725
Product Serial Number: C8FAA89AH
Product Code : 0593133
Module Code : 0204496
Basic Production Code: 059P7P9
PPM SW Version : V 07.00 11-09-12 RM-647 (c) Nokia ED
ADSP Version : p V 07.00\n11-09-12\nRM-647\n(c) NMP\ned
MCU SW Version : V 07.00 11-09-12 RM-647 (c) Nokia
HW Version : 1005
UEM Version : 1328
UPP Version : 8850
LCD Version : WIN:SERI:91 NT7542
********** SIMLOCK INFO **********
CONFIG_DATA : 0010100000000000
PROFILE_BITS : 0000000000030002
ASIC : 11
PROVIDER : Default Test Operator

Block [1] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [2] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [3] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [4] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [5] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [6] 1:Open 2:Open 3:Open 4:Open 5:Open
Block [7] 1:Open 2:Open 3:Open 4:Open 5:Open
ST_LCD_TEST : PASSED

FACTORY SET TO : Full Factory Set
OK
FACTORY SET TO : User Data
OK
FACTORY SET TO : Leave Factory
OK
FACTORY SET TO : Service Center
OK
FACTORY SET TO : Software Upgrade
OK
FACTORY SET TO : Production Tune
OK


Sa power supply natin umaangat ang power piranggot lang so ibig sabihin ok ang power switch line
ngayon po ayaw mag on sa power supply kahit sa battery pero 3 times flashing na ako ok naman sya

mga nagawa kona sa unit ay jumper ung #2 salikod at pinag short kona ung local sa malapit sa terminal na 10k pero same parin

no power
 
Mukang Ok naman ang Linya ng LCD pero di ko pa sya na try. Muka lang

Base kasi sa napansin ko sa Reading ng Power Supply Digital + Analog Reader Piranggot lang ung angat at hindi stable ang power nya. ung angat nya sa reading at isang guhit tapos pag bitay mo sa switch baksak din sya.

Malamang po sa idea ko lang ay power po.

Action taken ko pala sa Unit ay
-Jumper LCD #2 to resistor at back
-Clean the board
-Check Power Switch ways , Battery COnnector
-Flash at ATF
-Rehot Board Mild
-Hardware Remove Cover IC Parts and Reflow Mild
-Flashing Again and still have Power and Good in FLashing
- Still No Luck No power in Battery and No reading in power Supply in Software Ok ang Power nya
 
kong ok naman lahat ng linya so sa lcd yan palitan muna para d na sasakit ulo mo.......kc pag cra ang lcd hnd mo tlga yan ma e on...............
 
RTO na po Please Close na po, Di kaya ng bulsa ng CLient ko ung LCD para n syang bumili ng Bago na may CAM haizzzz
 
You must log in or register to reply here.
Back
Top