Duplicated
Registered
ILABAS KU NA ANG HINIHINTAY NG LAHAT
ANG MODEM MUNG NA SIRA OR BIGLANG NAG POWER LIGHT LED ONLY
Tuts for B315s-936 power light only.
*Basahin lahat muna bago simulan.. may mga revisions.
A. STEPS:
working lang on following conditions:
1. Successful sa new openline ng 936 pero after ng reset e powerlight pa rin.
2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD.
Kung hindi mo naabot yung "Done/Remove battery and put it again" bka hindi gumana.
Una sa lahat eto muna dapat gawin
flash mu na sa firmware na eto mamili nalang kaya sa dalawa kung anung gusto nyung gamiten
1.)Middle East firmware credits to Sir rexzero walang usb mode
B315s-936_Polkomtel21.311.to.MiddleEast21.300.rar
eto password: rolly_tech
2.)Zain Firmware credits kay Sir mulot
B315s-936_Zain by rolly_tech.rar
eto password: rolly_tech
Eto ang steps ng pag flash
1. Open Balong USB Downloader
- Click Detect
- Locate usblsafe-b315.bin
- Load
- Pag 100% na close.
2. Open Firmware Folder
- Click go_hdlc
- Enter
3. Open Huawei R215 Flash
- Locate 3G PC UI Interface (select)
- Flash
- Locate .hmf file
- Antayin na may nakasulat na Done/Remove battery and put it again..
- Close
4. Unplug Power, Unplug USB, unplug Flasher
5. pagkatapos ang flash power led parin po yan proceed to b. steps
B.Steps:
Note: Reported po na mas successful pag gawin muna yung new 936 flashing by sir Jansen Ramos.
http://www.symbianize.com/showthread.php?t=1371603
Mostly lahat nang successful e ginamit Win7 64bit OS.
1. press:
a. press power button at wps button at reset button then plug power sabay sabay press yung 3 button tapos saksak power cable, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
b. pag hindi umilaw yung red, press power at wps buttons, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
2. Hintayin umilaw blue light at last two signal bars. wag galawin.
3. Hintayin na power light na lang. plug usb to usb cord.
4. Check sa device drivers dapat may unknown o Android ADB Interface ka.
5. Ipalit and driver na - Android ADB Interface, mag have disk ka. piliin mo yung nasa folder adb_driver_windows
6. Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"
Dapat yung cmd mo "c:\files>"
8. Sa CMD, type
Code:
fastboot -i0x12d1 getvar product</pre>
9. Dapat may magpakita na - product: balongv7r2
10. Sa CMD ulit, type
Code:
fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin</pre>
11. Dapat may response na "OK".
12. Reboot na or hugotin na yung power adaptor
done na buhay na ulit modem mo.
eto yung links na kelangan
b315s-936_for_powerlight_only.rar
eto password: rolly_tech
kung dipa openline yung modem nyu nung nag power led nalang sya eto
solution jan
Sign in 192.168.8.1 admin/admin
Unlocking sim
1. Open B315s toolbox
- admin admin
- API Control
- api/device/mode
<request>
<mode>2</mode>
</request>
- Write Directly to API
- Click Debug, check kung ang response ay OK
2.Open telnet
- telnet 192.168.8.1
- type or copy paste
at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0
at^reset
maraming salamat sa gumawa ng tuts at credits sa mga gumawa at sa symbianize.com
mag rereboot ang modem at pag katapos factory reset sa setting ng modem debrand and unlock na modem mu
pa hit nalang po ng like kung magustuhan nyu
eto screen shots
marameng salamat po
ANG MODEM MUNG NA SIRA OR BIGLANG NAG POWER LIGHT LED ONLY
Tuts for B315s-936 power light only.
*Basahin lahat muna bago simulan.. may mga revisions.
A. STEPS:
working lang on following conditions:
1. Successful sa new openline ng 936 pero after ng reset e powerlight pa rin.
2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD.
Kung hindi mo naabot yung "Done/Remove battery and put it again" bka hindi gumana.
Una sa lahat eto muna dapat gawin
flash mu na sa firmware na eto mamili nalang kaya sa dalawa kung anung gusto nyung gamiten
1.)Middle East firmware credits to Sir rexzero walang usb mode
B315s-936_Polkomtel21.311.to.MiddleEast21.300.rar
eto password: rolly_tech
2.)Zain Firmware credits kay Sir mulot
B315s-936_Zain by rolly_tech.rar
eto password: rolly_tech
Eto ang steps ng pag flash
1. Open Balong USB Downloader
- Click Detect
- Locate usblsafe-b315.bin
- Load
- Pag 100% na close.
2. Open Firmware Folder
- Click go_hdlc
- Enter
3. Open Huawei R215 Flash
- Locate 3G PC UI Interface (select)
- Flash
- Locate .hmf file
- Antayin na may nakasulat na Done/Remove battery and put it again..
- Close
4. Unplug Power, Unplug USB, unplug Flasher
5. pagkatapos ang flash power led parin po yan proceed to b. steps
B.Steps:
Note: Reported po na mas successful pag gawin muna yung new 936 flashing by sir Jansen Ramos.
http://www.symbianize.com/showthread.php?t=1371603
Mostly lahat nang successful e ginamit Win7 64bit OS.
1. press:
a. press power button at wps button at reset button then plug power sabay sabay press yung 3 button tapos saksak power cable, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
b. pag hindi umilaw yung red, press power at wps buttons, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
2. Hintayin umilaw blue light at last two signal bars. wag galawin.
3. Hintayin na power light na lang. plug usb to usb cord.
4. Check sa device drivers dapat may unknown o Android ADB Interface ka.
5. Ipalit and driver na - Android ADB Interface, mag have disk ka. piliin mo yung nasa folder adb_driver_windows
6. Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"
Dapat yung cmd mo "c:\files>"
8. Sa CMD, type
Code:
fastboot -i0x12d1 getvar product</pre>
9. Dapat may magpakita na - product: balongv7r2
10. Sa CMD ulit, type
Code:
fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin</pre>
11. Dapat may response na "OK".
12. Reboot na or hugotin na yung power adaptor
done na buhay na ulit modem mo.
eto yung links na kelangan
b315s-936_for_powerlight_only.rar
eto password: rolly_tech
kung dipa openline yung modem nyu nung nag power led nalang sya eto
solution jan
Sign in 192.168.8.1 admin/admin
Unlocking sim
1. Open B315s toolbox
- admin admin
- API Control
- api/device/mode
<request>
<mode>2</mode>
</request>
- Write Directly to API
- Click Debug, check kung ang response ay OK
2.Open telnet
- telnet 192.168.8.1
- type or copy paste
at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0
at^reset
maraming salamat sa gumawa ng tuts at credits sa mga gumawa at sa symbianize.com
mag rereboot ang modem at pag katapos factory reset sa setting ng modem debrand and unlock na modem mu
pa hit nalang po ng like kung magustuhan nyu
eto screen shots
marameng salamat po
