*****
Dynex
Source/Input 2580
Hold Vol down on TV and hold the (#1) button on remote
*
Element China
Menu 0000 > menu 1147
*
Insignia
Input 2580 (TV is on)
*
LG / Zenith
Hold MENU on TV and MENU on remote for 5 to 10 seconds,
*
LG Service Menu Instructions
Method 1
Press and Hold button on remote as well as TV panel at the same time for a few seconds.
Method 2
Press and hold the {MENU} button on the remote and the {MENU}
button on the TV at the same time for at least 5-7 seconds
*
Mitsubishi
Menu 123 or Menu 2470 (TV is on)
*
NEC
While powering ON, hold "MENU" or "INPUT" on TV,
*
Panasonic
Hold [ VOL-- ] on TV, press and hold menu button on remote.
*
Philips
Push Menu , select 062596
*
Polaroid
Hold [VOL--] and [CHANNEL--] or hold [VOL+] and [CHANNEL+]
(TV is on)
*
Proscan
In customer menu go to setup, select parental control menu,enter 0000 then select “clear channel list”.
*
RCA
Menu 1147
*
Sanyo
Hold VOL Down on TV, press and hold #1 button on remote,
VOL will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.
*
Samsung
Mute 182 power
Samsung (European)
Power off, Info - Menu - Mute - Power,
*
Seiki
Menu 0000
*
Sharp
Menu, 1999
Menu, 3481
Menu, 1147
*
Sony
Hold “arrow up” on Remote and push power button on TV (TVis ON)
*
Symphony
Source/input 2580
*
Toshiba
On Menu, select “Installation”, then “ System Information” press the right arrow button.
(“System Information” will change to “Factory Reset” or something similar)
*
Service Toshiba LED
to enter the Service mode adjust the volume to zero , press the mute twice from the remote and press the menu button on the TV (fourth button from the bottom and marked p and decree it shares) ..to exit the menu shut the TV to enter Click on Oak control of top and bottom of the image , as specified in red Press "Mute" & 'Menu" buttons on the remote control simultaneously.Press "Menu"' button on the remote control, and enter {4 => 7 => 2 => 5}Press 'Volume Down' button on the front panel of the TV and press and hold digit '9' on the remote control. OR With No Menu displayed on the panel, press 'AV" & "F' buttons simultaneously.Enter code {1 => 0 => 4 => 8} by the remote control.
OR
Press 'Mute' button on the remote control.Press 'Mute' button again. While keep pressing the 'Mute' button, press "Menu" button on the TV SET."S" will be displayed at top right corner of the screen.Press 'TV (ANT) / VIDEO" button on TV; to get a single Horizontal Line On | Off [to adjsut screen voltage]Press 'TV (ANT) / VIDEO' button on the Remote Control; to select internal Test Signals.Use 'Ch Up | Ch Dn' buttons to call an item to adjust.Use 'Vol Up | Vol Dn' buttons to adjust the data value to selected item.To make adjustment menu On \ OFF, press 'Menu' button.To 'initialize' the memory IC (QA02), press "Recall + Channel Up" button on the 'TV'.Press 'Recall + Channel Dn" button on the 'TV', to initialize self diagnostic data.
*
Vestel
Menu 4725 then select "RESET"
*
Vision Quest
Source / Input 2580
*
Vizio
menu under “Help” tab is Factory Default enter 0000
*
Panasonic
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds
*
AOC
TV mode adjust volume to zero, press mute key and press number key 9 8 7 6 .
*
AKAI Service Menu
Method 1
Press the MENU key.
Then press the 1, 9, 7, & 9 keys.
The Service Menu will now be displayed on screen.
To exit service mode, power off the TV.
===
*
AKAI Service Menu
Method 2
Turn TV power on.
Press the MENU, 8, 2, 0, & 2, keys on the remote control.
The Service Menu will now be displayed on screen.
To exit service mode, power off the TV.
===
*
FUNAI:
FUNAI Service Menu:
Funai LCD Service Access Code
Method 1
Turn the TV power on using the POWER key on the TV.
Press the STANDBY-ON, 2, 7, 1, & MUTE keys on the remote control.
The Service Menu will be displayed on screen.
To exit service mode, press the STANDBY-ON key on the remote.
Funai
LCD Service Access Code
Method 2
Turn the TV power off.
Press and hold MENU key on the TV.
Then press the STANDBY-ON key on the TV.
The TV will turn on with the Service Menu displayed on screen. To exit service mode,
press the STANDBY-ON key on the TV.
*
Funai LCD Service Access Code
Method 3
Turn the TV power off.Press and hold SETUP key on the TV.
Then press the STANDBY-ON key on the TV.
The TV will turn on with the Service Menu displayed on screen.
To exit service mode, press the STANDBY-ON key on the TV.
Funai LCD Service Access Code
Method 4
Press the CH down & VOL down keys at same time.
Then press the MENU key.
The Service Menu displayed on screen.
To exit service mode, turn the TV power off.
*
Funai LCD Service Access Code
Method 5
Press the CH up, CH down & VOL up keys at same time.
Then press the MENU key.
The Service Menu displayed on screen.
To exit service mode, turn the TV power off.
===
*
HP Service Menu:
While the LCD TV is on, unplug the AC power cable.
Then while pressing the INPUT & VOL down keys on the remote, plug the AC power cable back into the wall outlet.
When it powers up you will see a small letter "k" appear in brackets on the screen.
Then on the TV, press and hold down the VOL down & CH down keys and release.
CH up & CH down keys navigate through screen menu.
VOL up & VOL down keys adjust various field values.
Turn the TV off to exit the Service mode.
===
*
HITACHI Service Menu:
There are many Hitachi reset codes try either one until the right code works.
Hitachi TV Service Method
Turn the TV power on
Press the MENU, MENU, 8, SELECT, keys on the remote.
The Service Menu will be displayed on screen.
Use the UP DOWN keys to select items.
Use the LEFT RIGHT keys to change the data.
Press the EXIT key to exit the Service mode.
*
Hitachi TV Service Method 2
Turn the TV power off.
Press and hold the INPUT key on the TV then press the POWER key.
Hold both keys until the TV turns on with the Service Menu displayed on screen.
Use the UP DOWN keys to select specific field options.
Use the LEFT RIGHT keys to change data values.
Press the EXIT key to exit the Service mode.
*
Philips lcd led tv service code
22PFL 4407\V7 LCD MENU+2580
22PFL5557/V7 LED MENU+2580
24PFL5557\V7 LED MENU+2580
24PFL5957\V7 LED MENU+2580
32PFL4537\V7 LED MENU+2580
32PFL4737/V7 LED MENU+2580
32PFL5537\V7 LED MENU+2580
32PFL5937\V7 LED MENU+2580
22PFL5237\V7 LED MENU+2580
24PFL3457\V7 LCD MENU+1950
24PFL5007\V7 LED MENU+1950
24PFL5237/V7 LED MENU+1950
24PFL5637/V7 LCD MENU+195LL0
24PFL5957\V7 LCD MEMU+1950
32PFL3057\V7 LCD MENU+1950
32PLF5007/V7 LED MEMU+1950
32PFL5237\V7 LED MENU+1950
32PFL5537\V7 LCD MENU+1950
32PFL5637\V7 LCD MENU+2580
32PFL6357\V7 LED MENU+1950
32PFL6577\V7 LCD MENU+1950
32PFL7977\V7 LED MENU+1950
42PFL3457\V7 LED MENU+1950
42PFL6357V7 LED MENU+1590
42PFL6577\V7 LED MENU+1950
42PFL7357\V7 LED MENU+1950
42PFL7977\V7 LED MENU+1950
46PFL8577\V7 LED MENU+1950
58PFL9577\V7 LED MENU+1950
40PFL4757\V7 LED MENU+2580
42PFL6977\V7 LED MENU+1950
*
LCD LED TV Service Modes and open code by Imran Ashra Khan WhatsApp +923139292880
Here we can show you some factory service mode only for professional Technicain .
( Note : Don't disturb any setting during the operation without knowing the proper function )
Samsung and Sony Service mode Based on CV628-B42
CV338-B42 and CV338-A50 Boards
Source 2580
Source 2583
Source 2587
Also other china universal boards service mode By Imran Ashraf
Menu 1147
Menu 1183
Menu 1185
Menu 1187
*
COBY
Enter menu, Hi-Lite “audio” then enter 8893 Mode/Source 2580
*
Dynex
Source/Input 2580
Hold Vol down on TV and hold the (#1) button on remote
*
Element
Menu 0000 > menu 1147
*
Haier
Pull up menu, Hi-Lite “audio” then enter 8893.
*
Insignia USA
Input 2580 (TV is on)
*
LG / Zenith
Hold MENU on TV and MENU on remote for 5 to 10 seconds,
*
Mitsubishi/Mitsui
Menu 123 or Menu 2470 (TV is on)
*
NEC
While powering ON, hold "MENU" or "INPUT" on TV,
*
Panasonic
Hold [ VOL-- ] on TV, press and hold menu button on remote.
*
Philips
Push Menu , select 062596
*
Polaroid
Hold [VOL--] and [CHANNEL--] or hold [VOL+] and [CHANNEL+]
(TV is on)
*
Proscan
In customer menu go to setup, select parental control menu,
enter 0000 then select “clear channel list”.
*
RCA China board
Menu 1147
*
Sanyo
Hold VOL Down on TV, press and hold #1 button on remote, VOL will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.
*
Samsung
Mute 182 power
*
Samsung (European)
Power off, Info - Menu - Mute - Power,
Seiki
Menu 0000
*
Sharp
Menu, 1999
Menu, 3481
Menu, 1147
While holding [ VOL– & INPUT ] buttons on TV plug in set when “K ” appears push (VOL– & CHANNEL-)
*
Sony
Hold “arrow up” on Remote and push power button on TV (TV is ON)
*
Symphony
Source/input 2580
*
Toshiba
On Menu, select “Installation”, then “ System Information” press the right arrow button.
(“System Information” will change to “Factory Reset” or something similar)
*
Service Toshiba LED
to enter the Service mode adjust the volume to zero , press the mute twice from the remote and press the menu button on the TV (fourth button from the bottom and marked p and decree it shares) .. to exit the menu shut the TV to enter Click on Oak control of top and bottom of the image , as specified in red
*
Vestel
Menu 4725 then select "RESET"
*
Vision Quest
Source / Input 2580
*
Vizio
menu under “Help” tab is Factory Default enter 0000
*
AOC
TV mode adjust volume to zero, press mute key and press number key 9 8 7 6 .
*
TCL service mode = Press MENU, Select CONTRAST then enter 9735 or 1950 you will enter Factory mode and Design mode respectively.
Micromax
The TV has 3 types of Service Mode
1) Design Menu - Can access all other modes through this - Access to Overscan and other settings
*
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 1, 9, 5 and 0 in series, Design Menu will appear in the left top of screen
*
2) Factory Menu - Access to color calibration & WB settings
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 9, 7, 3 and 5 in series, Factory Menu will appear in the left top of screen
*
3) Service Menu - Random stuff
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 9, 7, 0 and 5 in series, Service Menu will appear in the left top of screen
*
COBY
Enter menu, Hi-Lite “audio” then enter 8893 Mode/Source 2580...
Dynex
Source/Input 2580
Hold Vol down on TV and hold the (#1) button on remote
*
Element China
Menu 0000 > menu 1147
*
Insignia
Input 2580 (TV is on)
*
LG / Zenith
Hold MENU on TV and MENU on remote for 5 to 10 seconds,
*
LG Service Menu Instructions
Method 1
Press and Hold button on remote as well as TV panel at the same time for a few seconds.
Method 2
Press and hold the {MENU} button on the remote and the {MENU}
button on the TV at the same time for at least 5-7 seconds
*
Mitsubishi
Menu 123 or Menu 2470 (TV is on)
*
NEC
While powering ON, hold "MENU" or "INPUT" on TV,
*
Panasonic
Hold [ VOL-- ] on TV, press and hold menu button on remote.
*
Philips
Push Menu , select 062596
*
Polaroid
Hold [VOL--] and [CHANNEL--] or hold [VOL+] and [CHANNEL+]
(TV is on)
*
Proscan
In customer menu go to setup, select parental control menu,enter 0000 then select “clear channel list”.
*
RCA
Menu 1147
*
Sanyo
Hold VOL Down on TV, press and hold #1 button on remote,
VOL will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.
*
Samsung
Mute 182 power
Samsung (European)
Power off, Info - Menu - Mute - Power,
*
Seiki
Menu 0000
*
Sharp
Menu, 1999
Menu, 3481
Menu, 1147
*
Sony
Hold “arrow up” on Remote and push power button on TV (TVis ON)
*
Symphony
Source/input 2580
*
Toshiba
On Menu, select “Installation”, then “ System Information” press the right arrow button.
(“System Information” will change to “Factory Reset” or something similar)
*
Service Toshiba LED
to enter the Service mode adjust the volume to zero , press the mute twice from the remote and press the menu button on the TV (fourth button from the bottom and marked p and decree it shares) ..to exit the menu shut the TV to enter Click on Oak control of top and bottom of the image , as specified in red Press "Mute" & 'Menu" buttons on the remote control simultaneously.Press "Menu"' button on the remote control, and enter {4 => 7 => 2 => 5}Press 'Volume Down' button on the front panel of the TV and press and hold digit '9' on the remote control. OR With No Menu displayed on the panel, press 'AV" & "F' buttons simultaneously.Enter code {1 => 0 => 4 => 8} by the remote control.
OR
Press 'Mute' button on the remote control.Press 'Mute' button again. While keep pressing the 'Mute' button, press "Menu" button on the TV SET."S" will be displayed at top right corner of the screen.Press 'TV (ANT) / VIDEO" button on TV; to get a single Horizontal Line On | Off [to adjsut screen voltage]Press 'TV (ANT) / VIDEO' button on the Remote Control; to select internal Test Signals.Use 'Ch Up | Ch Dn' buttons to call an item to adjust.Use 'Vol Up | Vol Dn' buttons to adjust the data value to selected item.To make adjustment menu On \ OFF, press 'Menu' button.To 'initialize' the memory IC (QA02), press "Recall + Channel Up" button on the 'TV'.Press 'Recall + Channel Dn" button on the 'TV', to initialize self diagnostic data.
*
Vestel
Menu 4725 then select "RESET"
*
Vision Quest
Source / Input 2580
*
Vizio
menu under “Help” tab is Factory Default enter 0000
*
Panasonic
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds
*
AOC
TV mode adjust volume to zero, press mute key and press number key 9 8 7 6 .
*
AKAI Service Menu
Method 1
Press the MENU key.
Then press the 1, 9, 7, & 9 keys.
The Service Menu will now be displayed on screen.
To exit service mode, power off the TV.
===
*
AKAI Service Menu
Method 2
Turn TV power on.
Press the MENU, 8, 2, 0, & 2, keys on the remote control.
The Service Menu will now be displayed on screen.
To exit service mode, power off the TV.
===
*
FUNAI:
FUNAI Service Menu:
Funai LCD Service Access Code
Method 1
Turn the TV power on using the POWER key on the TV.
Press the STANDBY-ON, 2, 7, 1, & MUTE keys on the remote control.
The Service Menu will be displayed on screen.
To exit service mode, press the STANDBY-ON key on the remote.
Funai
LCD Service Access Code
Method 2
Turn the TV power off.
Press and hold MENU key on the TV.
Then press the STANDBY-ON key on the TV.
The TV will turn on with the Service Menu displayed on screen. To exit service mode,
press the STANDBY-ON key on the TV.
*
Funai LCD Service Access Code
Method 3
Turn the TV power off.Press and hold SETUP key on the TV.
Then press the STANDBY-ON key on the TV.
The TV will turn on with the Service Menu displayed on screen.
To exit service mode, press the STANDBY-ON key on the TV.
Funai LCD Service Access Code
Method 4
Press the CH down & VOL down keys at same time.
Then press the MENU key.
The Service Menu displayed on screen.
To exit service mode, turn the TV power off.
*
Funai LCD Service Access Code
Method 5
Press the CH up, CH down & VOL up keys at same time.
Then press the MENU key.
The Service Menu displayed on screen.
To exit service mode, turn the TV power off.
===
*
HP Service Menu:
While the LCD TV is on, unplug the AC power cable.
Then while pressing the INPUT & VOL down keys on the remote, plug the AC power cable back into the wall outlet.
When it powers up you will see a small letter "k" appear in brackets on the screen.
Then on the TV, press and hold down the VOL down & CH down keys and release.
CH up & CH down keys navigate through screen menu.
VOL up & VOL down keys adjust various field values.
Turn the TV off to exit the Service mode.
===
*
HITACHI Service Menu:
There are many Hitachi reset codes try either one until the right code works.
Hitachi TV Service Method
Turn the TV power on
Press the MENU, MENU, 8, SELECT, keys on the remote.
The Service Menu will be displayed on screen.
Use the UP DOWN keys to select items.
Use the LEFT RIGHT keys to change the data.
Press the EXIT key to exit the Service mode.
*
Hitachi TV Service Method 2
Turn the TV power off.
Press and hold the INPUT key on the TV then press the POWER key.
Hold both keys until the TV turns on with the Service Menu displayed on screen.
Use the UP DOWN keys to select specific field options.
Use the LEFT RIGHT keys to change data values.
Press the EXIT key to exit the Service mode.
*
Philips lcd led tv service code
22PFL 4407\V7 LCD MENU+2580
22PFL5557/V7 LED MENU+2580
24PFL5557\V7 LED MENU+2580
24PFL5957\V7 LED MENU+2580
32PFL4537\V7 LED MENU+2580
32PFL4737/V7 LED MENU+2580
32PFL5537\V7 LED MENU+2580
32PFL5937\V7 LED MENU+2580
22PFL5237\V7 LED MENU+2580
24PFL3457\V7 LCD MENU+1950
24PFL5007\V7 LED MENU+1950
24PFL5237/V7 LED MENU+1950
24PFL5637/V7 LCD MENU+195LL0
24PFL5957\V7 LCD MEMU+1950
32PFL3057\V7 LCD MENU+1950
32PLF5007/V7 LED MEMU+1950
32PFL5237\V7 LED MENU+1950
32PFL5537\V7 LCD MENU+1950
32PFL5637\V7 LCD MENU+2580
32PFL6357\V7 LED MENU+1950
32PFL6577\V7 LCD MENU+1950
32PFL7977\V7 LED MENU+1950
42PFL3457\V7 LED MENU+1950
42PFL6357V7 LED MENU+1590
42PFL6577\V7 LED MENU+1950
42PFL7357\V7 LED MENU+1950
42PFL7977\V7 LED MENU+1950
46PFL8577\V7 LED MENU+1950
58PFL9577\V7 LED MENU+1950
40PFL4757\V7 LED MENU+2580
42PFL6977\V7 LED MENU+1950
*
LCD LED TV Service Modes and open code by Imran Ashra Khan WhatsApp +923139292880
Here we can show you some factory service mode only for professional Technicain .
( Note : Don't disturb any setting during the operation without knowing the proper function )
Samsung and Sony Service mode Based on CV628-B42
CV338-B42 and CV338-A50 Boards
Source 2580
Source 2583
Source 2587
Also other china universal boards service mode By Imran Ashraf
Menu 1147
Menu 1183
Menu 1185
Menu 1187
*
COBY
Enter menu, Hi-Lite “audio” then enter 8893 Mode/Source 2580
*
Dynex
Source/Input 2580
Hold Vol down on TV and hold the (#1) button on remote
*
Element
Menu 0000 > menu 1147
*
Haier
Pull up menu, Hi-Lite “audio” then enter 8893.
*
Insignia USA
Input 2580 (TV is on)
*
LG / Zenith
Hold MENU on TV and MENU on remote for 5 to 10 seconds,
*
Mitsubishi/Mitsui
Menu 123 or Menu 2470 (TV is on)
*
NEC
While powering ON, hold "MENU" or "INPUT" on TV,
*
Panasonic
Hold [ VOL-- ] on TV, press and hold menu button on remote.
*
Philips
Push Menu , select 062596
*
Polaroid
Hold [VOL--] and [CHANNEL--] or hold [VOL+] and [CHANNEL+]
(TV is on)
*
Proscan
In customer menu go to setup, select parental control menu,
enter 0000 then select “clear channel list”.
*
RCA China board
Menu 1147
*
Sanyo
Hold VOL Down on TV, press and hold #1 button on remote, VOL will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.
*
Samsung
Mute 182 power
*
Samsung (European)
Power off, Info - Menu - Mute - Power,
Seiki
Menu 0000
*
Sharp
Menu, 1999
Menu, 3481
Menu, 1147
While holding [ VOL– & INPUT ] buttons on TV plug in set when “K ” appears push (VOL– & CHANNEL-)
*
Sony
Hold “arrow up” on Remote and push power button on TV (TV is ON)
*
Symphony
Source/input 2580
*
Toshiba
On Menu, select “Installation”, then “ System Information” press the right arrow button.
(“System Information” will change to “Factory Reset” or something similar)
*
Service Toshiba LED
to enter the Service mode adjust the volume to zero , press the mute twice from the remote and press the menu button on the TV (fourth button from the bottom and marked p and decree it shares) .. to exit the menu shut the TV to enter Click on Oak control of top and bottom of the image , as specified in red
*
Vestel
Menu 4725 then select "RESET"
*
Vision Quest
Source / Input 2580
*
Vizio
menu under “Help” tab is Factory Default enter 0000
*
AOC
TV mode adjust volume to zero, press mute key and press number key 9 8 7 6 .
*
TCL service mode = Press MENU, Select CONTRAST then enter 9735 or 1950 you will enter Factory mode and Design mode respectively.
Micromax
The TV has 3 types of Service Mode
1) Design Menu - Can access all other modes through this - Access to Overscan and other settings
*
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 1, 9, 5 and 0 in series, Design Menu will appear in the left top of screen
*
2) Factory Menu - Access to color calibration & WB settings
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 9, 7, 3 and 5 in series, Factory Menu will appear in the left top of screen
*
3) Service Menu - Random stuff
Using the remote, enter the “Picture” submenu in the OSD; choosing the “contrast” item and press the 9, 7, 0 and 5 in series, Service Menu will appear in the left top of screen
*
COBY
Enter menu, Hi-Lite “audio” then enter 8893 Mode/Source 2580...
Last edited:
