DOWNLOAD DING DING defi phantom hang on logo done by tested firmware

[21volcano]

TOOLS
CM2 @ USB CABLE

PROCEDURE
-Open CM2 then select SPD Module
*Extract file after download
*Click Setting TAB
*Select CPU mode SP [SC7730..SC7731] eMMC [Crev/Android 6.x]
*Select Flash tab
*Select PAC button to select PAC FILE
*Check update NVM before Flashing

-Open device phone
*Press Volume down
*Insert Usb cable
*Just wait until write data ok
FWhttp://www.mediafire.com/file/udrxx2bs4n7bsqe/Defi_Phantom.rar
password: pass

ANT-GSM

21VOLCANO-LAGUNA-CHAPTER

 

[zetroc75]

salamt po dito CL 21volcano...

 

[remarbz718]

Ayos boss dagdag kaalaman....

 

[raixie]

maraming salamat po boss...

 

[21volcano]

HIT THANKS BOTTON NALANG

 

[21volcano]

 

[boynextdoor]

nice one bro ...keep sharing usefull info.....

 

[jainald]

slamat boss 21volcano super tested

 

[abetskiy boy]

maraming salamt tested walng kaba sa dibdib

 

[FAROK]

slamat s pag share. boss..

 

[rolyngalleto]

SALAMAT sa share boss

 

[rolyngalleto]

mga bossing pwd ba RD tools ang gamitin dito?

 

[jael1968]

Up ko lang boss pwede ba ito sa rd tools..

 

[21volcano]

Up ko lang boss pwede ba ito sa rd tools..

dko sure sir convet mo sa pacfile

 

[tata]

Patulong kung my pass salamat po

 

[jepong]

tested sa Cm2 boss

 

[Arjay16]

good job

 

[damsa2304]

boss lam nyo po ba ung pag flash sa spflashtool ng firmware ng ding ding defi phantom thanks and advance mga sir

 

[JULAY20]

tested boss salamat

log's

======= Flash
Files set for flashing :
[ MCU ] : SC77xx Infinity Package

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
 -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

 ====  Wait for phone...

Phone found! [ 3 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0     
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!

[FL] : Enabled NVM update. Will program all NVM images found in FW !


PMTManager : Load 0x19 records
PMTManager : PMT Update Ok!
Flashing now

Update BootCode : u-boot-spl-16k.bin
Write Data ...
Write Data Ok!

Update BootCode : u-boot.bin
Erase block ...
Block erase Ok!
Write Data ...
Write Data Ok!

Write FSImage : prodnv.img
Write Data ...
Write Data Ok!

Write CodeData : sc7731C_CP0_modem.bin
Write Data ...
Write Data Ok!

Write CodeData : DSP_DM_Gx.bin
Write Data ...
Write Data Ok!

Update NVM image : nvitem_w.bin
Update NVM Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : sc8830g_modem_CP2_WCN_Trunk_W17.27.4_Release.bin
Write Data ...
Write Data Ok!

Update NVM image : nvitem_wcn.bin
Update NVM Data Ok!

Erase Block : RuntimeData
Erase block ...
Block erase Ok!

Write CodeData : logo_540x960.bin
Write Data ...
Write Data Ok!

Write CodeData : fblogo_540x960.bin
Write Data ...
Write Data Ok!

Write CodeData : boot.img
Write Data ...
Write Data Ok!

Write FSImage : system.img
Write Data ...
Write Data Ok!

Erase Block : PERSIST
Erase block ...
Block erase Ok!

Write FSImage : cache.img
Write Data ...
Write Data Ok!

Write CodeData : recovery.img
Write Data ...
Write Data Ok!

Erase Block : MISC
Erase block ...
Block erase Ok!

Write CodeData : sysinfo.img
Write Data ...
Write Data Ok!

Write FSImage : userdata.img
Write Data ...
Write Data Ok!


Elapsed: 00:04:30

Reconnect Power/Cable!