gt-e1200y phone lock kkagawa ko lang mga bos
1.open cm2 spd
2.spd6530-samsung
3.user data/Forensic/Others
4.check. Read user code
5.Ginamit ko pala sa usb ung sa z3x
maraming salamat po sana makatulog
@POWERD BY; CM2@
Card found: S/N : 67083FB1 , v0136
Chinese Miracle II [SPD module] v 1.27
Set mode to : SPD6530_SAMSUNG
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Device boot not done
Check Drivers
Try again
Reconnect Power/Cable!
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Device boot not done
Check Drivers
Try again
Reconnect Power/Cable!
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 19 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6530 , FDLStat : 00C0
[0] Flash DIE : 00C8 0060 0017 0000
[0] Flash VEN : GigaDevice , GD25LQ64
[0] Flash CAP : 00800000
Check data... Can take some time
User Code : 012615
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
DONE.
1.open cm2 spd
2.spd6530-samsung
3.user data/Forensic/Others
4.check. Read user code
5.Ginamit ko pala sa usb ung sa z3x
maraming salamat po sana makatulog
@POWERD BY; CM2@
Card found: S/N : 67083FB1 , v0136
Chinese Miracle II [SPD module] v 1.27
Set mode to : SPD6530_SAMSUNG
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Device boot not done
Check Drivers
Try again
Reconnect Power/Cable!
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Device boot not done
Check Drivers
Try again
Reconnect Power/Cable!
Operation : Read User Code [ v1.27 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 19 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6530 , FDLStat : 00C0
[0] Flash DIE : 00C8 0060 0017 0000
[0] Flash VEN : GigaDevice , GD25LQ64
[0] Flash CAP : 00800000
Check data... Can take some time
User Code : 012615
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
DONE.
