sa lahat po ng mga jtag users... makikisuyo sana.. papaguide lang ako pano ijtag itong tanggap ko na G530fz... dinala sakin to hang on logo at error lahat sa hard reset.
ito yung ginawa ko,
1.flash ko sa odin. ayun patay sya
2. bumili ako ng pang jtag. easy jtag plus po. (baguhan lang po sa paggamit nito first time) kaya di ko alam gagawin. ayaw po magkonek.
3. kaya bumili ako ng emmc at pinalitan ko
4.pin out then salpak sa easy jtag ayun nagkonek
5.dahil di ko alam gagawin ,download ako sa support.. nilagyan ko yung rom 2 at rom 3 at yung boot cfg tapos write all rom (kaso error sa writing)
6. tapos ginawa ko factory reset then write all rom ulit. (error pa din sa writing)
7. tapos factory reset+format all ko then write all rom (error pa din sa writing)
ito po yung logs
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1956 mV
CMD Active Level: 2452 mV
EMMC Device Information :
EMMC CID: 150100514E5730304D0BF1BDC89581FF
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture Name: SAMSUNG , EMMC NAME: QNW00M , EMMC NAME (HEX): 514E5730304D , S/N: F1BDC895 , rev. 0x0B
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Manufacture Date: 8/2014
EMMC ROM 1 (Main User Data) Capacity: 0 MB (FFFFFFFFFFFFFE00)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 32640 KB (000001FE0000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 32640 KB (000001FE0000)
EMMC GP1 (GP Partition 1) Capacity: 255 MB , ENH , WR_REL (00000FF80000)
EMMC GP2 (GP Partition 2) Capacity: 255 MB (00000FF80000)
EMMC GP3 (GP Partition 3) Capacity: 255 MB (00000FF80000)
EMMC GP4 (GP Partition 4) Capacity: 255 MB (00000FF80000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: UNKNOWN
Boot configuration [PARTITION_CONFIG]: 0xFF , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0xFF , reserved
H/W Reset Function [RST_N_FUNCTION]: 0x03, Reserved
Supported partition features [PARTITIONING_SUPPORT]: 0xFF
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: QNW00M_F1BDC895_20180302_044144.extcsd
EMMC Init completed.
Reading from: ROM3 , start: 0x000000000000 , size: 0x000000000200
Output file: C:\Program Files\Z3X\EASYJTAGPLUS\EMMC__ROM3_000000000000_000000000200.bin
eMMC switching to ROM3
Reading partition...
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #3
Too many errors. Reading has been stopped
Try the "Skip unreadable blocks" option
pa guide po sana step by step pano gagawin.. pasensya na po baguhan lang po sa pagjjtag
at pinakamahalaga po ay pakitama po yung mga mali ko pong steps na ginawa.
ito yung ginawa ko,
1.flash ko sa odin. ayun patay sya
2. bumili ako ng pang jtag. easy jtag plus po. (baguhan lang po sa paggamit nito first time) kaya di ko alam gagawin. ayaw po magkonek.
3. kaya bumili ako ng emmc at pinalitan ko
4.pin out then salpak sa easy jtag ayun nagkonek
5.dahil di ko alam gagawin ,download ako sa support.. nilagyan ko yung rom 2 at rom 3 at yung boot cfg tapos write all rom (kaso error sa writing)
6. tapos ginawa ko factory reset then write all rom ulit. (error pa din sa writing)
7. tapos factory reset+format all ko then write all rom (error pa din sa writing)
ito po yung logs
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1956 mV
CMD Active Level: 2452 mV
EMMC Device Information :
EMMC CID: 150100514E5730304D0BF1BDC89581FF
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture Name: SAMSUNG , EMMC NAME: QNW00M , EMMC NAME (HEX): 514E5730304D , S/N: F1BDC895 , rev. 0x0B
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Manufacture Date: 8/2014
EMMC ROM 1 (Main User Data) Capacity: 0 MB (FFFFFFFFFFFFFE00)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 32640 KB (000001FE0000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 32640 KB (000001FE0000)
EMMC GP1 (GP Partition 1) Capacity: 255 MB , ENH , WR_REL (00000FF80000)
EMMC GP2 (GP Partition 2) Capacity: 255 MB (00000FF80000)
EMMC GP3 (GP Partition 3) Capacity: 255 MB (00000FF80000)
EMMC GP4 (GP Partition 4) Capacity: 255 MB (00000FF80000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: UNKNOWN
Boot configuration [PARTITION_CONFIG]: 0xFF , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0xFF , reserved
H/W Reset Function [RST_N_FUNCTION]: 0x03, Reserved
Supported partition features [PARTITIONING_SUPPORT]: 0xFF
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: QNW00M_F1BDC895_20180302_044144.extcsd
EMMC Init completed.
Reading from: ROM3 , start: 0x000000000000 , size: 0x000000000200
Output file: C:\Program Files\Z3X\EASYJTAGPLUS\EMMC__ROM3_000000000000_000000000200.bin
eMMC switching to ROM3
Reading partition...
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -3, DATA RCV Timeout Error ... Retry #3
Too many errors. Reading has been stopped
Try the "Skip unreadable blocks" option
pa guide po sana step by step pano gagawin.. pasensya na po baguhan lang po sa pagjjtag
at pinakamahalaga po ay pakitama po yung mga mali ko pong steps na ginawa.
