How to Test a Transistor
Method 1 of 4: Understanding Transistors
1
A transistor is basically 2 diodes that share one end. The shared end is called the base and the other 2 ends are called the emitter and collector.
The collector accepts an input current from the circuit, but it can't send the current through the transistor until allowed to by the base.
The emitter sends a current out into the circuit, but only if the base allows the collector to pass the current through the transistor to the emitter.
The base acts like a gate. When a small current is applied to the base, the gate opens and a large current can flow from the collector to the emitter.
20mb image hosting
2
Transistors may operate by junctions or field effects, but both come in two basic types.
An NPN transistor uses a positive semiconductor material (P-type) for the base and negative semiconductor material (N-type) for the collector and emitter. On a circuit diagram, an NPN transistor shows an emitter with the arrow pointing out ("Never Points iN" aids remembering).
A PNP transistor uses an N-type material for the base and P-type material for the emitter and collector. The PNP transistor show an emitter with the arrow pointing in ("Points iN Permanently" is the memorizer).
Method 2 of 4: Setting Up the Multimeter
free image host
2
Turn the selector knob to the diode test function.
Method 3 of 4: Testing When You Know the Base, Emitter and Collector
free upload pictures
1
Determine which leads are the base, emitter and collector. The leads are round or flat wires extending from the bottom of the transistor. They may be labeled on some transistors or you may be able to determine which lead is the base by studying the circuit diagram.
post image online
adult photo hosting
3
Touch the red probe to the emitter. Read the display on the multimeter and note whether the resistance is high or low.
4
Move the red probe to the collector. The display should give the same reading as when you touched the probe to the emitter.
free picture upload
image url
5
Remove the black probe and clamp the red probe to the base.
6
Touch the black probe to the emitter and collector. Compare the reading on the multimeter's display to the readings you got previously.
If the previous readings were both high and the current readings are both low, the transistor is good.
If the previous readings were both low and the current readings are both high, the transistor is good.
If both readings you receive with the red probe are not the same, both readings with the black probe are not the same, or the readings don't change when switching probes, the transistor is bad.
Method 4 of 4: Testing When You Don't Know the Base, Emitter and Collector
image hosting over 5mb
4
Touch the black probe to each of the other 2 leads.
If the display shows high resistance when each of the leads are touched, you have found the base (and you have a good PNP transistor).
If the display shows 2 different readings for the other 2 leads, clamp the red probe to another lead and repeat the test.
After clamping the red probe to each of the 3 leads, if you don't get the same high resistance reading when touching the other 2 leads with the black probe, you have a bad PNP transistor.
types of transistor
picture uploading
Method 1 of 4: Understanding Transistors
1
A transistor is basically 2 diodes that share one end. The shared end is called the base and the other 2 ends are called the emitter and collector.
The collector accepts an input current from the circuit, but it can't send the current through the transistor until allowed to by the base.
The emitter sends a current out into the circuit, but only if the base allows the collector to pass the current through the transistor to the emitter.
The base acts like a gate. When a small current is applied to the base, the gate opens and a large current can flow from the collector to the emitter.
20mb image hosting
2
Transistors may operate by junctions or field effects, but both come in two basic types.
An NPN transistor uses a positive semiconductor material (P-type) for the base and negative semiconductor material (N-type) for the collector and emitter. On a circuit diagram, an NPN transistor shows an emitter with the arrow pointing out ("Never Points iN" aids remembering).
A PNP transistor uses an N-type material for the base and P-type material for the emitter and collector. The PNP transistor show an emitter with the arrow pointing in ("Points iN Permanently" is the memorizer).
Method 2 of 4: Setting Up the Multimeter
free image host
2
Turn the selector knob to the diode test function.
Method 3 of 4: Testing When You Know the Base, Emitter and Collector
free upload pictures
1
Determine which leads are the base, emitter and collector. The leads are round or flat wires extending from the bottom of the transistor. They may be labeled on some transistors or you may be able to determine which lead is the base by studying the circuit diagram.
post image online
adult photo hosting
3
Touch the red probe to the emitter. Read the display on the multimeter and note whether the resistance is high or low.
4
Move the red probe to the collector. The display should give the same reading as when you touched the probe to the emitter.
free picture upload
image url
5
Remove the black probe and clamp the red probe to the base.
6
Touch the black probe to the emitter and collector. Compare the reading on the multimeter's display to the readings you got previously.
If the previous readings were both high and the current readings are both low, the transistor is good.
If the previous readings were both low and the current readings are both high, the transistor is good.
If both readings you receive with the red probe are not the same, both readings with the black probe are not the same, or the readings don't change when switching probes, the transistor is bad.
Method 4 of 4: Testing When You Don't Know the Base, Emitter and Collector
image hosting over 5mb
4
Touch the black probe to each of the other 2 leads.
If the display shows high resistance when each of the leads are touched, you have found the base (and you have a good PNP transistor).
If the display shows 2 different readings for the other 2 leads, clamp the red probe to another lead and repeat the test.
After clamping the red probe to each of the 3 leads, if you don't get the same high resistance reading when touching the other 2 leads with the black probe, you have a bad PNP transistor.
types of transistor
picture uploading
