livestrong
Premium Account
instruction
Turn the phone ON and wait until it fully starts up
Set the phone into the Manufacture Mode by entering *#*#2846579#*#* code (follow the instruction from the Enable Manufacture Mode manual)
Connect the phone to PC using USB cable
Install phone drivers (only if the phone is connected for the first time).
Select "HISILICON" platform from the tab menu in the upper left side of the software
Wait for 10 seconds
Go to "Unlock" tab
Select "Android Adapter PCUI". If there is no such port, select "Comneon Mobile High-speed Modem"
Press "Unlock" button
The message "Unlock done… OK" indicates that procedure has been completed successfully
Disconnect the handset
A phone is unlocked
done 7.0 version
Pack 1: Activated
Pack 2: Activated
Pack 3: Not activated
--------- 2018-11-04 15:35:05 ---------
SigmaKey 2.29.07 HiSi: Direct unlock
Connecting....
Android Adapter PCUI (COM230), Provider: HUAWEI Technologies CO.,LTD, Driver ver.: 1.0.26.0, Date: 18/05/2016, USB\Vid_12D1&Subclass_13&Prot_22
Firmware: NRD90M test-keys, Date: Tue Sep 5 12:50:01 CST 2017, Provider: tef/normal
Boot Version: Chipset-austin 5.0.0.3(0ECD)_BOOT, FastBoot Version: Chipset-austin 5.0.0.3(0ECD)_FASTBOOT
Recovery Version: (unknow), System Version: System 5.0.0.57(0VI9)
Removing firmware protection....Done
Software IMEI: 862836035509862
Unlocking phone...Done
Restarting phone...Done
CESYA NA PO WALANG SCREENSHOOT sobrang hina ng net ko at lagi error sa image uploading..
but this is tested
Turn the phone ON and wait until it fully starts up
Set the phone into the Manufacture Mode by entering *#*#2846579#*#* code (follow the instruction from the Enable Manufacture Mode manual)
Connect the phone to PC using USB cable
Install phone drivers (only if the phone is connected for the first time).
Select "HISILICON" platform from the tab menu in the upper left side of the software
Wait for 10 seconds
Go to "Unlock" tab
Select "Android Adapter PCUI". If there is no such port, select "Comneon Mobile High-speed Modem"
Press "Unlock" button
The message "Unlock done… OK" indicates that procedure has been completed successfully
Disconnect the handset
A phone is unlocked
done 7.0 version
Pack 1: Activated
Pack 2: Activated
Pack 3: Not activated
--------- 2018-11-04 15:35:05 ---------
SigmaKey 2.29.07 HiSi: Direct unlock
Connecting....
Android Adapter PCUI (COM230), Provider: HUAWEI Technologies CO.,LTD, Driver ver.: 1.0.26.0, Date: 18/05/2016, USB\Vid_12D1&Subclass_13&Prot_22
Firmware: NRD90M test-keys, Date: Tue Sep 5 12:50:01 CST 2017, Provider: tef/normal
Boot Version: Chipset-austin 5.0.0.3(0ECD)_BOOT, FastBoot Version: Chipset-austin 5.0.0.3(0ECD)_FASTBOOT
Recovery Version: (unknow), System Version: System 5.0.0.57(0VI9)
Removing firmware protection....Done
Software IMEI: 862836035509862
Unlocking phone...Done
Restarting phone...Done
CESYA NA PO WALANG SCREENSHOOT sobrang hina ng net ko at lagi error sa image uploading..
but this is tested