REFERENCE iphone itunes error codes solution

[ChedRick]

iphone itunes error codes solution




Error -23
Hardware - Error message -23 of iPad6 indicate the battery run out
Solution
Charge or change the battery

Error -1
Hardware - Error occurs when baseband cpu, baseband flash or baseband pm ic get damaged or dry
soldered from board or else some other hardware fault which preventing baseband function to update during restore ios.

Error 1
Hardware - Related to error -1 but not directly point to bb cpu or flash might be something else hardware.

Error 2
Software - Check for issues with third-party security software.
Hardware - Connection issue between phone hardware via usb to computer. Could be firmware flash chip dry soldered.
Solution

1. Check power supply output of baseband power;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value

Error 3
Hardware - BB or BB supporting components are damaged. Check BB voltage regulator chips.
Solution

1. Check power supply output of baseband power;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value;
4. Repair with instrument as there is mismatch between baseband EEPROM and data

Error 4
Software - Check for issues with third-party security software.
Hardware - Connection issue between phone hardware via usb to computer. Could be firmware flash chip dry soldered.

Error 6
Software - Unable to resize partition due to full storage problem at final stage of updating firmware.
The error may be bypassed (restart and do exit recovery) but you probably need to re-update it one more time
Hardware - Connection issue between phone hardware via usb to computer. Could be nand chip Issue.


Error 9
The most common error which has too many reasons even vary on different iDevice models. All and 100% cause of error 9 not yet revealed as it not same for all.
Software- Restart pc/mac. Re-install latest version of itunes. Try with latest ios version clean install.
Try with different pc. Try with original usb cable. Try with different usb port on pc.
Hardware - Sufficient power/voltage not present to finish software operation. Battery, battery connector,
dock flex cable, charging ic and charging related parts, power ic, cpu, shorted caps on board, etc etc.

Error 10
Software - Try with a new IOS file. Direct restore from online.

Error 11
Software - Use latest version of itunes. New ios file. Restart pc
Solution
Re-download new firmware

Error 12
Software - Firmware shutdown verification.[
Solution
Re-download new firmware

Error 13
Software - Use latest version of itunes. Beta software issue. Try with MAC computer with MAC OS.
Hardware - Use original usb cable. Don't use usb hub put direct.
Solution

1. Re-download new firmware;
2. Replace the reboot wire or dock flex of the phone

Error 14
Software - Use latest version of itunes and MAC OS. Might be issues with third-party security software.
Hardware - Device isn't bootable. Nand issue. USB Problem. Check the USB connection and try other direct ports or maybe the USB cable is an older one.

Error 15
Hardware -Mostly NAND has problems, without ruling out NAND power supply problems
Solution

1. Replace the NAND if it is damaged;
2. Reinstall the NAND if it has pseudo soldering;
3. Measure the mainboard GND resistance value if the path has problems, or maybe the power supply is not available

Error 16
Hardware - In the path from baseband CPU to baseband EEPROM, mostly baseband EEPROM has problems
Solution
Check baseband EEPROM for pseudo soldering or damage, and measure mainboard GND resistance value if the path has problems

Error 17
Software - Try to restore with clean and new ios. Restore Direct from online.

Error 18
Software - Device file system is corrupted. Don't update but clean restore should solve this issue.

Error 20
Software - Problem with third party security software. If it's happened with new itunes try with older one. Usually happens when try to downgrade. Try with beta ios.
Hardware - Don’t use external hub direct connect to usb. Try with another and original usb cable. Try with different pc/mac.
Solution
Manually enter DFU mode to reboot again

Error 21
Mostly error 20 is a hardware issue which cause of low power.
Software - Restore in dfu mode. Try with different pc, usb cable, usb port.
Hardware - There is not enough power to finish software operation. Check battery and it way, charging ic, sensor cables. Check nand. Remove board from housing,
only put battery and charging/dock flex cable and try to restore software.

Error 23
Mostly hardware issue.
Software - Do usual troubleshot, itunes, new ios etc.
Hardware - Might be communication problem.
Check battery, bb cpu and bb flash.
Solution
Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged, and the part under water damage is peripheral capacitor or baseband power.

Error 26
Software - Try with new ios, direct restore from online through itunes.
Hardware - Check regular flash ic.
Solution
Check baseband CPU or EEPROM for pseudo soldering or damage, and measure mainboard GND resistance value if the path has problems

Error 27
Software - Just restore it don’t use update option. Use latest itunes and ios file.
Hardware - Check battery, battery connection and usb connectivity.

Error 28
Hardware - The problem is a bad dock connector on the iPhone. Must change the connector.
If you have tried almost everything, reset the logic board (leave uncharged for five days or remove battery for half an hour), then pwn and restore. If this doesn't
work, the memory of your device is damaged.
Solution

1. Main CPU lower layer has pseudo soldering or damage;
2. In a few cases, NAND has problems, such as pseudo soldering or damage

Error 29
You might need to change the battery.
If iTunes is already open, quit and reopen it.
Make sure that you have the latest version of iTunes.
Check for issues with third-party security software.
Make sure that your USB cable, computer, and network are reliable. Then try twice more to restore your iPhone, iPad, or iPod.
If you still see the error message, you can check for outdated or modified software.

Error 31
Apple Mobile Device USB Drive Problem, reinstall latest itunes, change usb cable, don’t use hub. Try with another pc/mac.
Solution

1. Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value to test the path

Error 34
Low disk space in your computer, related to memory of your pc.

Error 37
Attempting restore with an IPSW that was stitched with blobs not for your device (Usually a good thing if restoring with a geek grade beta IPSW or
with your own creation). To boot, simply open redsn0w. Do fix recovery and tether boot after. Do not lock or device's LCD will fail.

Error 40
NAND chip is dead (confirm with ASR output from restore log).

Error 45
Same with Error 6, in terms of resizing partition issue. But this may occur at the very beginning of restore process.

Error 47
Baseband circuits have problems: baseband EEPROM or baseband CPU
Solution

1. Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value to test the path

Error 48
Dead/Malfunctioning baseband chip during restore/update, BB voltage regulator ic issue might be, try again and if it doesn't work, a hardware fix will be necessary.
Solution

1. Repair with instrument as there is mismatch between baseband EEPROM and data;
2. Check baseband EEPROM or baseband CPU for pseudo soldering or damage;
3. Corresponding parts should be replaced as baseband EEPROM and baseband CPU mismatch with main CPU data

Error 50
Baseband CPU has faults
Solution

1. Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value to test the path

Error 56
Most likely a dead/glitched Touch ID sensor. Try restoring the latest firmware in DFU mode.
Take out the SIM card and try restoring in DFU mode. If still occurring, take your device to apple.

Error 91
NAND circuits have problems
Solution

1. Replace the NAND if it is damaged;
2. Reinstall the NAND if it has pseudo soldering;
3. Measure the mainboard GND resistance value if the path has problems, or maybe the power supply is not available.

Error 1002
Baseband circuits or NAND circuits have problems
Solution

1. Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value to test the path;
4. Replace the NAND if it is damaged; reinstall the NAND if it has pseudo soldering.

Error 1003
Baseband circuits or NAND circuits have problems
Solution

1. Check power supply output of baseband power, focusing on checking whether the power supply is grounded, and if it is grounded, mostly the baseband CPU is damaged;
2. Check baseband power or baseband CPU for pseudo soldering or damage;
3. Check mainboard GND resistance value to test the path;
4. Replace the NAND if it is damaged; reinstall the NAND if it has pseudo soldering.

Error 1004
This is caused by a failure to match the Baseband Nonce currently in memory to the nonce returned in the Baseband Firmware SHSH blob.
Use TinyUmbrella and "Kick Device Out Of Recovery" to boot.

Error 1005
NAND circuits have problems
Solution

1. Replace the NAND if it is damaged;
2. Reinstall the NAND if it has pseudo soldering;
3. Measure the mainboard GND resistance value if the path has problems, or maybe the power supply is not available.

Error 1011
This is caused by recovery mode being in userland.

Error 1013
This means that the baseband did not get updated. Either remove the gs.apple.com entry from your hosts file and let the baseband
upgrade or if you want to preserve the baseband just jailbreak at this point to boot it up.
Restart computer; change computer; reinstall system, if the device is always in restoring mode:
XP users can jump from restoring mode with ibus; MAC users can use iNdependence or similar other sw.
Solution
Perform server authentication

Error 1014
This occurs when you try to downgrade your device's baseband.

Error 1015
This error is common when downgrading iPhones and 3G iPads. The problem occurs when the device's baseband has a higher version
number than the baseband in the firmware you restored to.
Just set auto-boot true in iRecovery or use iREB/TinyUmbrella/RecBoot.1 In case this is not working use Pwnagetool to create a custom firmware
WITHOUT the iPad baseband, put your device in pwned DFU Mode and restore via iTunes.
Solution
Reboot again after repair of computer system

Error 1050
Bad response from gs.apple.com OR need iREB for preparing the device for restoring to custom IPSW

Error 1394
Older IOS. Try with latest one.
Baseband prevent the update itself. Sometime happens with refurbish device

Error 1413
Restart computer; change USB port, try with older itunes, restore online. reinstall system. Try another pc/mac.

Error 1415
Restart computer; change USB port; reinstall system.

Error 1417
Restart computer; change USB port; reinstall system.

Error 1418
Restart computer; change USB port; reinstall system.

Error 1428
Restart computer; change USB port; reinstall system.

Error 1600
Custom firmware can't be restored on a device with DFU Mode. The software of the device isn't patched.
Using a jailbreak tool, enter a pwned DFU Mode. During that process the software gets patched and the custom firmware should run without any problems.
If truly stuck (even with an regular iTunes Restore), edit the hosts file.
GetDeviceID: failed for iBoot (experienced on Windows 8)
Solution

1. Check main CPU for pseudo soldering or damage;
2. Check CPU power supply or power supply path elements

Error 1601
Usb error, bad itunes, registry/host issue in windows.
Solution

1. Check main CPU for pseudo soldering or damage;
2. Check CPU power supply or power supply path elements

Error 1602
Restart computer; change computer; reinstall system.
If this error occurred during an Apple TV restore, then unplug the Apple TV from the power cable, after you entered the recovery or DFU mode, and then try it again.
Solution
Check for USB power supply or system problems

Error 1603
False kernelcache patch. Known on damaged bundles from unofficial PwnageTool distributions.

Error 1604
Device was not pwned (signature checks were not blocked). Custom firmware can't be restored. Can also happen when there's a problem with the IPSW.

Error 1611
iTunes tried to enter the Restore Mode, but the device turned back to the Recovery Mode.
Solution

1. Replace the NAND if it is damaged;
2. Reinstall the NAND if it has pseudo soldering;
3. Measure the mainboard GND resistance value if the path has problems, or maybe the power supply is not available.

Error 1618
Missing system files or corrupt data in iTunes installation. Try to uninstall iTunes,
restart computer, install again. This error also occurs for iTunes in Windows 8 for reasons currently unknown.

Error 1619
Tunes is too old and couldn't read the iPhone in Recovery or DFU Mode. Please update iTunes and try it again.

Error 1644
PSW was moved during prepare with iTunes. Try it again and don't move the IPSW.

Error 1646
iTunes expected the device to be in a different state (Example: booted into iOS rather than jumping to iBEC).

Error 1667
Occurs when device is unplugged while the "iTunes will erase and restore your iPhone to
iOS and will verify the restore with Apple." dialog is shown. Check USB connections and try again.

 

[ChedRick]

Error 1646
Error message 1669 will appear in the case of EEPROM data error or loss, or burnout of iPhone6S dock connector
Solution

1. Repair with instrument as there is mismatch between baseband EEPROM and data;
2. Check baseband EEPROM for pseudo soldering or damage;
3. Corresponding parts should be replaced as baseband EEPROM and baseband CPU mismatch with main CPU data .

Error 2001
Check USB hub.

Error 2002
Tunes can't connect because another program is using it or it's disconnected during the Apple Server check.
Solution
Change the network and reconnect the Apple server

Error 2003
Connection problem; change USB cable and check USB port.
sn0wbreeze failed to restore IPSW; unplug and plug iDevice and try again
Solution
Check USB circuits or computer

Error 2005
Problem connecting. Probably a hardware failure.
Supposedly reinstalling the USB drivers fixed the problem.
Solution
Check battery condition or detect the testing pin path

Error 2006
Replace the USB cable with a newer one and/or disconnect all other USB devices, then retry.

Error 2009
f you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore.
If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore.
If that does not resolve the issue, see Error 1604 above. If the issue persists, it may be related to conflicting security software on your computer.
Solution
Check the computer, and it is better to use Apple computer for reboot to ensure stability and less error message

Error 3002
Update to an older firmware isn't working, because Apple is no longer handing out SHSHs for the device/firmware combination.
Or a timeout checking Apple server - retry later.
This error also happens if you try to Update with a local TSS server (TinyUmbrella tool) and probably also when connecting to Cydia Server. Use Restore instead.
Error 3002 represents no update ramdisk when pressing Shift+Check for updates.

Error 3004
No internet connection during the firmware restore.
iTunes can't connect to gs.apple.com. Maybe Port 80 and Port 443 is blocked. Open it on your router.
Solution
Check USB circuits, data wire or computer

Error 3011
Bad hosts file. The SHSH request couldn't be completed. No connection to the Apple Server, Open your host file and remove any lines with gs.apple.com."

Error 3014
Bad hosts file. The SHSH request couldn't be completed. No connection to the Apple Server, Cydia Server or localhost (for TinyUmbrella).
iTunes can't connect to gs.apple.com. Maybe Port 80 and Port 443 is blocked. Open it on your router.
Solution
Bad hosts file. The SHSH request couldn't be completed. No connection to the Apple Server, Cydia Server or localhost (for TinyUmbrella).
iTunes can't connect to gs.apple.com. Maybe Port 80 and Port 443 is blocked. Open it on your router.

Error 3049
CPU circuits have problems
Solution

1. Check main CPU for pseudo soldering or damage;
2. Check 1161111 CPU power supply or power supply path elements

Error 3123
Something dealing with movie rentals.

Error 3191
QuickTime may be corrupted. You must reinstall it before iTunes will work. Windows users, also try turning off Compatibility Mode for QuickTime[

Error 3194
Occurs when trying to install an old firmware and Apple's server disallows the installation. The only solution is to have the SHSH blob backed up and modify the
hosts file to point to Saurik's Cydia Server where they are backed up (or localhost if you have it yourself). Also happens if restoring to the latest iOS and the
hosts point to Cydia. Remove gs.apple.com lines in hosts file.
Another message that this error can display is "not eligible for requested build". Restore latest IOS with latest iTunes.

Error 3195
There is no SHSH blob for the firmware.
This is the same as "This device isn't eligible for the request build." but with an cache error.

Error 3200
You are trying to update to a firmware, when in fact, there is only a Restore Ramdisk.

Error 4013
Connection to device is lost after the "Preparing iPhone for Restore" step but before the phone is actually wiped causing it to boot normally.
Check USB connections and try again. Check battery and power way. Finally check nand ic, re-hot it would be work.

Error 4015
CPU upper layer circuits have problems
Solution

1. Check main CPU upper layer for pseudo soldering or damage;
2. Check CPU power supply or power supply path elements

Error 9008
Error downloading, check internet and try again.

Error 9807
Unknown error; try again

Error 11222
A security software you have installed may be conflicting with iTunes.

Error 11556
You're trying to access a section or a functionality that is not available in your country, for example iCloud in some countries.

Error 13019
Seems to be an issue with syncing media to the device... It only seems to happen on jailbroken devices.
Create new user, try syncing with new user's library. If that fails, restore. If it doesn't fail, then something on YOUR itunes Library is causing the error.

Error 20000
This error can also be caused by the iDevice rebooting during the "Extracting Firmware" stage of restore.

Error 20008
This happened on a Mac with TinyUmbrella running before restoring a firmware to the Apple TV.

0x80090318
Something dealing with programs monitoring Winsock.

0xEXXXXXX
Mostly usb relates issue either it software or hardware. So just check all hw and sw which is related to usb.


0xE800000F
Reboot your idevice and pc/mac with original usb cable try again.

0xE8000001
Device was suddenly unplugged. iTunes couldn't connect with the device. Try it again

0xE8000022
Error in your firmware files. Restore with latest file direct from online/real time.

0xE800003D
False permissions in the Carrier Bundle folder. Restore, update or fix the permissions from the carrier bundle to update the carrier settings via iTunes.

0xE800006B
Device was suddenly unplugged. iTunes couldn't connect with the device. Try it again.

0xE8000065
Error on USB connection. Unplug the device, reboot it, and plug it in again.

0xE8008001
IPA signature verification failed.

0xE800001F
Usb or registry on windows pc issue.

0xE8800084
Check usb port and cable. Reinstall itunes. Update pc/mac.