What's new
By:
PinoyTechnician

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

myphone my32L hang sa logo done sa aking sariling back up

jerrenn

jerrenn

Registered
Joined
May 27, 2015
Messages
393
Reaction score
152
Points
31
Location
Bulacan
pasa lag na ka ant natin si JMgadget from angono rizal dumayo dito sa shop at nagpa jolibbee:D:D:D

model:my32L
problem:hang sa logo:
action taken:flash sa cm2 sa sarili kung back up https://drive.google.com/open?id=0B1xUxK3PfM5EcXZtelRDLUVqZXM
password protected
procedure:
flashing
Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6592
BB_CPU_NME : [MediaTek] MT6592_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8A
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004B594C30304D1225740B30BE9F
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00LY
[eMMC] : FLASH_CID : 1501004B594C30304D1225740B30BE9F
[eMMC] : FLASH_BRT : 0x00080000 , 0x00080000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID : BB377C2F4B5AD82A0D74F48DFA8BB9CB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6592 , Project : qishang6592_wet_l , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : Unknown (not supported or without battery)

BL : Flash Pre-Erase
Total blocks to Erase : 3
Erase : 0x0000000000000000-0x0000000000100000
Erase : 0x0000000001D00000-0x00000000023A0000
Erase : 0x00000000041A0000-0x00000003A5D60000
Flash Pre-Erase Done, time used : 00:00:09

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_qishang6592_wet_l.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0014
Update PMT by user request
Repartition Done!

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : EBR2
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:03:47

Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : EBR2
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:00:58

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:05:18
Reconnect Power/Cable!
Click to expand...


then do factory reset sa cm2
Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6592
BB_CPU_NME : [MediaTek] MT6592_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8A
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004B594C30304D1225740B30BE9F
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00LY
[eMMC] : FLASH_CID : 1501004B594C30304D1225740B30BE9F
[eMMC] : FLASH_BRT : 0x00080000 , 0x00080000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID : BB377C2F4B5AD82A0D74F48DFA8BB9CB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear USERDATA
========================= Start =========================
4/3/2016 / 1:28:00 PM
=========================================================
Card found : S/N : D5F781510 , v0130
Chinese Miracle II [MTK module] v 1.43

Start at : [4/3/2016 / 1:28:29 PM]
Operation : Format FileSystem [ v1.43 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6592
BB_CPU_NME : [MediaTek] MT6592_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8A
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004B594C30304D1225740B30BE9F
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00LY
[eMMC] : FLASH_CID : 1501004B594C30304D1225740B30BE9F
[eMMC] : FLASH_BRT : 0x00080000 , 0x00080000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003AB400000
[eMMC] : FLASH_UCP : 15028 MiB [eMMC 16 GiB]
DEV RID : BB377C2F4B5AD82A0D74F48DFA8BB9CB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


Clear FRP ( Google Reset Protection )
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!

Done!
Elapsed: 00:00:58
Reconnect Power/Cable!
Click to expand...

then power ang pohone 3 to 10 mins bago mag vibrate
then result
2j5xago.jpg

24e9t38.jpg

sana makatulong sa inyu
 
MARAMING SALAMAT PRE!! Tested talaga lahat ng files mo, walang kaduda duda. Hindi sayang ang pasyal ko, province to province hahahaha.
 
congrats sir....sir pwede po ba pabulong ng passwor..tia
 
Last edited by a moderator:
pa pm ng password master...salamat sa pag bahagi....
 
sir pwede po pa pm ng password po..kelangan ko kc ito sir..tnx a lot
 
boss meron din akong sariling back up, may bin file at scatter pa pero bat kaya nadeads ang unit camera lang naman ang sira nun, ayaw mag open
 
bossing baka po pwede makahinge ng password salamat
 
jerrenn said:
pasa lag na ka ant natin si JMgadget from angono rizal dumayo dito sa shop at nagpa jolibbee:D:D:D

model:my32L
problem:hang sa logo:
action taken:flash sa cm2 sa sarili kung back up https://drive.google.com/open?id=0B1xUxK3PfM5EcXZtelRDLUVqZXM
password protected
procedure:
flashing



then do factory reset sa cm2


then power ang pohone 3 to 10 mins bago mag vibrate
then result
2j5xago.jpg

24e9t38.jpg

sana makatulong sa inyu
Click to expand...


paki update nmn po ng link boss at kung pwde pa pm ng password po

Thanks ng marami
 
You must log in or register to reply here.
Back
Top