What's new
By:
PinoyTechnician

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Need Help! Myphone MyA1

SantinO

SantinO

Registered
Joined
Feb 7, 2016
Messages
109
Reaction score
22
Points
1
Location
Lupon, Davao Oriental
help po mga master

hang sa logo ayaw mp flash hanggang erase salng sa cm2, na back up ko ok naman natapos sa back up.

eto logs

cm2 logs

Card found : S/N : 5DE63CBD , v0136
Chinese Miracle II [MTK module] v 1.58

Scatter Load Ok , BaseBand : MT6580 , Project : benrui6580_weg_m , Storage : EMMC
Files found : 9 , Set to Flash : 8
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : MyPhone
Device Model : MY801
Device CPU : MT6580
Device IntName : myA1
Device Version : 6.0
Device Compile : 11/6/2017 1:47:33 AM
Device Project : alps-mp-m0.mp1-V2.118_benrui6580.weg.m_P11
Device ExtInfo : MY801
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 12 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048607A35684A087
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048607A35684A087
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0x25B008AF4F04337F6C04AA502490184E
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6580 , Project : benrui6580_weg_m , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : Only one records found, and determined as universal
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3793 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000003320000
Erase : 0x00000000050A0000-0x00000000E0EE0000
Flash Pre-Erase Done, time used : 00:00:00

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_benrui6580_weg_m.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : FFFFFFFF
PartErr : Not initialized , will update PMT now ...
Repartition Failed! Something wrong with HW or BL? Try make "Flash Erase" first!

Operation Failed
Elapsed: 00:00:16
Reconnect Power/Cable!



nck logs

Flash files count is :11
Action : Firmware update.
Selected 0-By CPU: MT6580
Exe version: NCKDongle AndroidMTK 2.5.6.2
Scenario: Safe Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM12)
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6580_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 512 MB DRAM
----------------------------------------------------
EMMC: (28Gb+4096Mb) HYNIX 0x483447316404
EMMC FW VERSION: 86:00:00:00:00:00:00:00
EMMC CID: 90014A48344731 : 000000000000000000
EMMC UA SIZE: 0xe7000000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0xe7600000 [3.615 GB]
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM15)
Warning, flashing preloader disabled!
If you change android version, preloader must be flashed.
Flash EMMC Algo Start.
Starting flash.
Send preloader...
Error: S_DL_WRITE_PT_FAIL
Wait untill phone will start charging.
All done.
 
itest mo flash ic sa cm2
punta ka extra tab
check test flash icc
then make test
pag read only hardware na ang problem niyan
 
try nio munayung sinasabe ni boss Prince pag ayw prn try mo ung bngay ko sayo files
 
Kung nadedetect pa sa PC boss hardware test mo sa CM2 pag lumabas na read only na lang RTO na

vjNZTeG.png
 
eto po logs na lumabas sa hw test mga master

Card found : S/N : 5DE63CBD , v0136
Chinese Miracle II [MTK module] v 1.58

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048607A35684A087
Initialize Memory ...

[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2003
EMICFG_NOT_FOUND
TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!

Operation Failed
Elapsed: 00:00:05
Reconnect Power/Cable!
 
2nd attemp ko sa HW Test

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 12 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164048607A35684A087
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048607A35684A087
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 0x25B008AF4F04337F6C04AA502490184E
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Initial info read error! Erased or damaged FlashIC?!
Force eMMC test by user request

Processing Miscellaneous test
MSC : BatteryLevel : 3585 mV

[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , d1G4 , 0xE7000000 , 3696 MiB
[eMMC] : CID : 90014A4834473164048607A35684A087

[eMMC] : MODE : SQ-WR
[FAILED] : Probably, something wrong with eMMC! Check cable and battery!

Operation Failed
Elapsed: 00:00:22
Reconnect Power/Cable!
 
Try mo muna uninstall yang driver at cm2 mtk mo boss then clean registry edelete mo folder ng cm2mtk then restart
then install mo ulit yung driver at cm2mtk, then flash mo lang ulit baka mag-okey na siya kase parang may error
 
pag ayaw pa rin try mo mild reheat yung emmc baka siya may problema then reflash ulit
pag ayaw pa rin mag-okey gamitan mo na lang ng RTO crack para wala ng problema=)):))
 
You must log in or register to reply here.
Back
Top