O+ 8.31z Scatter FIles Backup via CM2MTK

[mANTra]

O+ 8.31z Scatter FIles Backup via CM2MTK


O+ 8.31z

Link
O+ 8.31z SCATTER FILE


PASSWORD PROTECTED
REQUEST PASSWORD HERE


FEEL FREE TO HIT THANKS BUTTON
​

 

[abetskiy boy]

boss pabulong ng pass

salamat

 

[mANTra]

boss pabulong ng pass

salamat

pm sent )

 

[rquebs]

pa ambon din ng password boss..salamat

 

[mANTra]

pa ambon din ng password boss..salamat

pm sent )

 

[Junel_05]

master pa pm ng pass nito salamat in advance...

 

[mANTra]

master pa pm ng pass nito salamat in advance...

pm sent )

 

[deathstalker]

Pa pm ng pass salamat po

 

[mANTra]

Pa pm ng pass salamat po

pm sent )

 

[FLAME216]

pbulong ng pass mga boss

 

[FLAME216]

pbulong ng pass mga boss

 

[mANTra]

pbulong ng pass mga boss

pm sent )

 

[Berdugo]

sir p bahagi n pass... salamat

 

[nalor]

bakit po ganito?
Unsupported Yet( or bad??? ) file selected!
yan po lumalabas tuwing ilalagay ko sa cm2 ang scatter

 

[tirador07]

boss password naman..salamat

 

[mondarte]

boss pabulong ng password salamat

 

[ernie78]

thanks master but bad file by CM2 version 1.58
but dont worries this file tested done by NCK easy done
thanks

Flash files count is :9
Action : Firmware update.
Selected Model: 0-By CPU: MT6572_NAND
Exe version: NCKDongle AndroidMTK 2.5.7.5
Scenario: [0]Safe Flash
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM13)
Boot mode: Preloader
Phone detected...Please wait
Sending DA agent, please wait...
BaseBand CPU :MT6572_S00
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 256 MB DRAM
----------------------------------------------------
NAND: (4Gb+2048Mb) [Hynix] H9TA4GH2GDMCPR
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 2048 SpareSize: 64 BMT Blocks 80
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : MediaTek DA USB VCOM (Android) (COM14)
Warning, flashing preloader disabled!
If you change android version, preloader must be flashed.
Flash NAND Algo Start.
Download firmware to flash now...
Wait untill phone will start charging.

after flash invalid imei easy done by NCK

IMEI[2] for write : 860332022962852
Scanning for presents meta ports...
Meta ports not detected, starting brom stage.
Phone must be off with battery inside.
Please insert USB cable now...
In some phones need to keep VOL- button untill inserting USB cable.
[13]Detected: MediaTek PreLoader USB VCOM (Android) (COM13)
\\?\usb#vid_0e8d&pid_2000#6&2b9940da&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Starting META mode, wait...
Restarting to meta,wait....
If drivers missing, please install CDC drivers.
This can take up to 5 min on slow phones.
If take too long, check device manager for drivers.
[21]META Port Detected: MediaTek USB VCOM (Android) (COM21)
USB\VID_0E8D&PID_2007\6&2B9940DA&0&2
Start sync target, waiting responce.....
[AP]BaseBand CPU : MT6572,S01
[AP]APP_VER: ZZA260PD_086AA_V8_0_0
[META]BaseBand CPU : MT6572, E01
[META]SW_VER : MOLY.WR8.W1315.MD.WG.MP.V1.P3
[META]HW_VER : HUAQIN72_WE_IBA_JB3_HSPA_HW
Meta mode conected ok, start reading phone....
IMEI to repair: [1] 860332022808329
Phone imei[1] : 860332022808329
IMEI to repair: [2] 860332022962852
Phone imei[2] : 860332022962852
Clean Boot flag ok.
All done.

big thanks TS

 

[b3t]

pa pm ng password .. salamat..

 

[marvin1226]

boss pa PM password salamat po

 

[monicks]

boss pwede hingi pass nito salamat

http://www.antgsm.com/showthread.php?t=83475&highlight=8.

https://www.4shared.com/get/WZ7Gh5pTba/831z.html

 

[jorge_2015]

boss,pa share password n2..thanks