SM-j100ml/ds dead boot done by MEDUSA PRO

cools802 · Dec 26, 2017

STEPs what to do...
1. connect the device
2. open EMMC service tab click "write ext_csd button (choose the file i attach in DL link).
3. write boot1 and boot2
4. write smj100ml srf file
5. go to "factory repair tab"
6. click "repair samsung devices using factory files"
7. select PIT file, then Add AP,BL,CSC,MODEM..
8. uncheck "REPARTITION"
9. click "write partition"
10. Done.....
11. assemble the unit and put it to DL mode....
12. open odin v3.09 reflash with J100ML_DXU0AOB3_OLC0AOB5 files are attach in DL link...
13. do not include the pit file
14. click "start button"
15. DONE.............tested 1001% by me.....

https://mega.nz/#!nUxGwbqJ!z8Uwq6RFHjkseWXZaY7GMHoQ9Hcvogdo4TaEWPICxGY PM me for password...

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A48344732621101A2AB188F12E5
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) A2AB188F
Manufacturing date : 01/2015
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1 (Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x1
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...Ok

Disk/Image size : e9000000 bytes
Device sector size : 512 bytes
Partition offset : 616448
Number of sectors : 2129920
Device Manufacturer : samsung
Device Platform : sc8830
Build ID : KTU84P
Display Build ID : KTU84P.J100MLDXS0AQB1
Release ID : 4.4.4
Device Model : SM-J100ML
Device Name : j13gthw
Architecture ABI : armeabi-v7a
Architecture ABI2 : armeabi
Build Description : j13gthw-user 4.4.4 KTU84P J100MLDXS0AQB1 release-keys

Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/H4G2b_25_12_2017_10_02_51.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.5.0; FW: 1.22.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: efs (00015800, 0000A000) 20 MB
P18: prodnv (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: CSC (00032800, 00064000) 200 MB
P23: system (00096800, 00208000) 1040 MB
P24: HIDDEN (0029E800, 00014000) 40 MB
P25: userdata (002B2800, 0048E000) 2332 MB

Selected pit file: C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/J13G.pit

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/MODEM_J100MLDXU0AOB4_REV02_CL_1898770.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/CSC_OLC_J100MLOLC0AOB5_CL366995_QB4171712_REV01_user_low_ship.tar.md5".

Writing PIT
Write data verification is enabled.
Writing. Please wait...

Switched to boot area partition 1.
Writing partition BOOT... Done.

Switched to user area.
Writing partition SBOOT... Done.
Writing partition SBOOT2... Done.
Writing partition wfixnv2... Done.
Writing partition WDSP... Done.
Writing partition MODEM... Done.
Writing partition PARAM... Done.
Writing partition KERNEL... Done.
Writing partition RECOVERY... Done.
Writing partition CSC... Done.
Writing partition system... Done.
Writing partition HIDDEN... Done.
Writing is finished.
SW: 1.5.0; FW: 1.22.

cools802 · Dec 26, 2017

[MENTION=44946]Seandre[/MENTION] you dont have medusa pro...brainless.... see the log...

ZOCHRALSKI · Dec 27, 2017

Thank sa pag share boss.....

baby maker · Dec 27, 2017

cools802 said:
[MENTION=44946]Seandre[/MENTION] you dont have medusa pro...brainless.... see the log...

sir ganun knb ka expert para sabihan mo ang isang ka member natin ng BRAINLESS? maramin dito ang jtag experts pero ni isa sa kanila ay walang ganyan klaseng post na nakakababa ng moral.Magtatanong ako sir..Paki explain anong connection ang cLK sa jtag?

cools802 · Dec 27, 2017

[MENTION=44946]Seandre[/MENTION] just read first the thread before you make a comment...or maybe you dont have a know how on emmc/jtag programming....just zipper your mouth...

JPhar · Dec 27, 2017

good day may medusa pro box aq sa pagkakaalam q dpa supported ang j100ml kay medusa kasi kung supported na malamang ung pending na limang j100ml ok na sana..

pakilagay ng ss kungh tunay yan boss salamat

melton · Dec 27, 2017

cools802 said:
STEPs what to do...
1. connect the device
2. open EMMC service tab click "write ext_csd button (choose the file i attach in DL link).
3. write boot1 and boot2
4. write smj100ml srf file
5. go to "factory repair tab"
6. click "repair samsung devices using factory files"
7. select PIT file, then Add AP,BL,CSC,MODEM..
8. uncheck "REPARTITION"
9. click "write partition"
10. Done.....
11. assemble the unit and put it to DL mode....
12. open odin v3.09 reflash with J100ML_DXU0AOB3_OLC0AOB5 files are attach in DL link...
13. do not include the pit file
14. click "start button"
15. DONE.............tested 1001% by me.....

https://mega.nz/#!nUxGwbqJ!z8Uwq6RFHjkseWXZaY7GMHoQ9Hcvogdo4TaEWPICxGY PM me for password...

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A48344732621101A2AB188F12E5
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) A2AB188F
Manufacturing date : 01/2015
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1 (Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x1
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...Ok

Disk/Image size : e9000000 bytes
Device sector size : 512 bytes
Partition offset : 616448
Number of sectors : 2129920
Device Manufacturer : samsung
Device Platform : sc8830
Build ID : KTU84P
Display Build ID : KTU84P.J100MLDXS0AQB1
Release ID : 4.4.4
Device Model : SM-J100ML
Device Name : j13gthw
Architecture ABI : armeabi-v7a
Architecture ABI2 : armeabi
Build Description : j13gthw-user 4.4.4 KTU84P J100MLDXS0AQB1 release-keys

Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/H4G2b_25_12_2017_10_02_51.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.5.0; FW: 1.22.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: efs (00015800, 0000A000) 20 MB
P18: prodnv (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: CSC (00032800, 00064000) 200 MB
P23: system (00096800, 00208000) 1040 MB
P24: HIDDEN (0029E800, 00014000) 40 MB
P25: userdata (002B2800, 0048E000) 2332 MB

Selected pit file: C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/J13G.pit

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/MODEM_J100MLDXU0AOB4_REV02_CL_1898770.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/CSC_OLC_J100MLOLC0AOB5_CL366995_QB4171712_REV01_user_low_ship.tar.md5".

Writing PIT
Write data verification is enabled.
Writing. Please wait...

Switched to boot area partition 1.
Writing partition BOOT... Done.

Switched to user area.
Writing partition SBOOT... Done.
Writing partition SBOOT2... Done.
Writing partition wfixnv2... Done.
Writing partition WDSP... Done.
Writing partition MODEM... Done.
Writing partition PARAM... Done.
Writing partition KERNEL... Done.
Writing partition RECOVERY... Done.
Writing partition CSC... Done.
Writing partition system... Done.
Writing partition HIDDEN... Done.
Writing is finished.
SW: 1.5.0; FW: 1.22.

pa pm po ng password. wla kasi sa support nd medusa ung srf ng j100ml.. salamat try q qng uubra pg my mpadaan

cools802 · Dec 27, 2017

[MENTION=44946]Seandre[/MENTION] tell you frankly you insult me, do not underestimate my post. READ THE PROCEDURE AND LOG EMMC REPORT...of my work...this procedure is tested by me many times....im just revealing this deadboot problem during normal usb programming using odin....to share to others encountering this same problem with this SMJ100ml/ds unit...

JPhar · Dec 27, 2017

cools802 said:
[MENTION=44946]Seandre[/MENTION] tell you frankly you insult me, do not underestimate my post. READ THE PROCEDURE AND LOG EMMC REPORT...of my work...this procedure is tested by me many times....im just revealing this deadboot problem during normal usb programming using odin....to share to others encountering this same problem with this SMJ100ml/ds unit...

good day boss j100ml is not supported by medusa pro how did you do this kindly make ur post clearer tnx..

fritzroy923 · Dec 27, 2017

Ang high blood naman ni TS... Calm down bro...
Wag magalit nagtatanong lang mga ka ANTECH.
Post mo nalang ang screen shot para maniwala
sila. Explain mo lang bro hindi namin alam e.
Peace bro....

cools802 · Dec 27, 2017

https://mega.nz/#!jFBXHZ4Z!F8t0RHYGVcCDTFYwujIPunB7fsVxu4o3y7t2mFSAofg
https://mega.nz/#!SZxg1QCB!9BlyUr9RqSfWIuPDhIIXPLfCpu877SM9YsoURh3TVis
https://mega.nz/#!7FIniToS!0e2asd0ZRPRl3GH7v6tmXWq9vdV_pWJLQ_gvjLKUx_k
https://mega.nz/#!eBIUzbTZ!Ci-ol3RnCTEnILobKUsvD3V0EhkliqUpRcXIwQ3SDeo
https://mega.nz/#!OBhnkSaD!Lq-X99IDG-E_y2dwYI7_oxg-525AhV3s7hOmkociNP8
https://mega.nz/#!OFhwEYLR!Q3GUg_ren63ggoPA9H8RNosndWVneLV_8FoAYKiQz9Q

that's the evidence..........ok ty....

cools802 · Dec 28, 2017

[MENTION=34230]Jhen_Cedric[/MENTION] its supported bro but you cant download it from support. just use my file which i was uploaded....even z3x jtag doesnt have a file for repair on sm-j100ml/ds....they only give a emmc pin out...download the file and see whats inside....just pm me for PW...thanks.......

https://mega.nz/#!vQYykAxb!MCfmZhQ4PV0sUwo30f658ya01Cmb5_6gzc7s0f1Or4s
SM-J100ml/ds pinout

vcc=2.8v and vccq=1.8v

rexelens · Dec 28, 2017

cools802 said:
[MENTION=34230]Jhen_Cedric[/MENTION] its supported bro but you cant download it from support. just use my file which i was uploaded....even z3x jtag doesnt have a file for repair on sm-j100ml/ds....they only give a emmc pin out...download the file and see whats inside....just pm me for PW...thanks.......

https://mega.nz/#!vQYykAxb!MCfmZhQ4PV0sUwo30f658ya01Cmb5_6gzc7s0f1Or4s
SM-J100ml/ds pinout

vcc=2.8v and vccq=1.8v

sir pinoytech po etong napuntahan nyong furom...wag pong masyadong mag english dumudugo ilong namin eh...at di rin po masama mag explain ng maayos lalo na't mga newbie kausap po natin....kasi di naman nila maiintindihan kahit logs lang kaya kaunting paliwanag lang po...tapos calm down po di po tayo magkaka away dito ...magkakakampi tayo dito...sige ka masilip ka ni boss pogi

joel1962 · Dec 28, 2017

kahapon nakagawa ako ng ganyan unit hang and auto off flash ko sa odin using AP files lang para walang deadboott done naman siya.

cools802 · Dec 28, 2017

@relexen salamat....i would like to ask a apology to seandre...sorry bro....

ZOCHRALSKI · Dec 28, 2017

GOOD JOB mga ka ANTECH sana ganito magkaintindihan agad ang bawat isa!!!

salamat din TS.

ZOCHRALSKI · Dec 28, 2017

cools802 said:
@relexen salamat....i would like to ask a apology to seandre...sorry bro....

GOOD JOB mga ka ANTECH sana ganito magkaintindihan agad ang bawat isa!!!

salamat din TS.

JPhar · Dec 28, 2017

cools802 said:
STEPs what to do...
1. connect the device
2. open EMMC service tab click "write ext_csd button (choose the file i attach in DL link).
3. write boot1 and boot2
4. write smj100ml srf file
5. go to "factory repair tab"
6. click "repair samsung devices using factory files"
7. select PIT file, then Add AP,BL,CSC,MODEM..
8. uncheck "REPARTITION"
9. click "write partition"
10. Done.....
11. assemble the unit and put it to DL mode....
12. open odin v3.09 reflash with J100ML_DXU0AOB3_OLC0AOB5 files are attach in DL link...
13. do not include the pit file
14. click "start button"
15. DONE.............tested 1001% by me.....

https://mega.nz/#!nUxGwbqJ!z8Uwq6RFHjkseWXZaY7GMHoQ9Hcvogdo4TaEWPICxGY PM me for password...

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A48344732621101A2AB188F12E5
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) A2AB188F
Manufacturing date : 01/2015
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1 (Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x1
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...Ok

Disk/Image size : e9000000 bytes
Device sector size : 512 bytes
Partition offset : 616448
Number of sectors : 2129920
Device Manufacturer : samsung
Device Platform : sc8830
Build ID : KTU84P
Display Build ID : KTU84P.J100MLDXS0AQB1
Release ID : 4.4.4
Device Model : SM-J100ML
Device Name : j13gthw
Architecture ABI : armeabi-v7a
Architecture ABI2 : armeabi
Build Description : j13gthw-user 4.4.4 KTU84P J100MLDXS0AQB1 release-keys

Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/H4G2b_25_12_2017_10_02_51.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.5.0; FW: 1.22.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: efs (00015800, 0000A000) 20 MB
P18: prodnv (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: CSC (00032800, 00064000) 200 MB
P23: system (00096800, 00208000) 1040 MB
P24: HIDDEN (0029E800, 00014000) 40 MB
P25: userdata (002B2800, 0048E000) 2332 MB

Selected pit file: C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/J13G.pit

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/BL_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/AP_J100MLDXU0AOB3_CL366995_QB4107924_REV01_user_low_ship_.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/MODEM_J100MLDXU0AOB4_REV02_CL_1898770.tar.md5".

Open file "C:/Users/Rolan802/Desktop/New folder (5)/J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware/CSC_OLC_J100MLOLC0AOB5_CL366995_QB4171712_REV01_user_low_ship.tar.md5".

Writing PIT
Write data verification is enabled.
Writing. Please wait...

Switched to boot area partition 1.
Writing partition BOOT... Done.

Switched to user area.
Writing partition SBOOT... Done.
Writing partition SBOOT2... Done.
Writing partition wfixnv2... Done.
Writing partition WDSP... Done.
Writing partition MODEM... Done.
Writing partition PARAM... Done.
Writing partition KERNEL... Done.
Writing partition RECOVERY... Done.
Writing partition CSC... Done.
Writing partition system... Done.
Writing partition HIDDEN... Done.
Writing is finished.
SW: 1.5.0; FW: 1.22.

papm aq ng password mu boss try q to sa medusa salamat

melton · Dec 28, 2017

[MENTION=23635]cools802[/MENTION] p try nga ng file mo pre.. pa pm ng pass.. salamat

alexan · Dec 28, 2017

maging mapagkumbaba... ang tapang ay pinapairal mismo kung kaharap mo na ang tao...

Marv · Dec 28, 2017

elo cools802 i would like to try your file but really hard to download on mega.nz can you reupload on mediafire thanks alot and one thing can you send me the password... cheer...

SM-j100ml/ds dead boot done by MEDUSA PRO

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Registered

Premium Account

Registered