REFERENCE Voice_V10i_NAND Pin Lock Remove Read Flash & Read NVRAM SuccessfulDone

[NEKNEKs]

Voice_V10i__MT6571__NAND Pin Lock Remove just 1 Click Time 00:26"Read Flash & Read NVRAM Successful, Done​

.:: BY ::.
..::: Chinese Miracle-2 MTK :::..

Reset Privacy Lock

Operation : Reset Privacy Lock [ v1.35 ]
 
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
 
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 009800BC009000660076001600080000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
 
Checking data ... 
Privacy Lock reset Ok!
 
Done!
Elapsed: 00:00:26
Reconnect Power/Cable!

After Reset Privacy Lock

Read Factory Firmware

Operation : Read Flash [ v1.35 ]
 
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
 
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 009800BC009000660076001600080000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
 
Reading Flash Conent now ... 
 
[Read Ok] : preloader_v13_n4gb2gb_2ggsm4_hvga
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : fat_empty.img
[Read Ok] : system.img
[Read Ok] : cache_empty.img
[Read Ok] : usrdata_empty.img
 
[ScatCFG] : MT6571 / V1.1.1 / v13_n4gb2gb_2ggsm4_ / NAND
FW Size : 249 MiB
Scatter saved to : C:\InfinityBox\CM2MTK\Flash\MT6571__NAND__v13_n4gb2gb_2ggsm4_
 
Done!
Elapsed: 00:02:47
Reconnect Power/Cable!

Read NVRAM

Operation : Read NVRAM [ v1.35 ]
 
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
 
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 009800BC009000660076001600080000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
 
[Info] : NAND , BaseBand Info not available!
Read Ok, MT6571_NAND.spnv saved
 
Done!
Elapsed: 00:00:24
Reconnect Power/Cable!